Krone 870 HDP Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 568

Krone 870 HDP Скачать руководство пользователя страница 62

Machine Description

62

Pos: 55.53 /Ü berschriften/Ü berschriften 3/K-O/NN adelschwi nge @ 158\mod_1365140055004_78.docx @ 1405035 @ 3 @ 1

5.8.5

Needle Yoke

Pos: 55.54 /BA/Bedienung /Groß packenpresse/Überlastsicherungen / Kuppl ungen / Sternr atsche / Scherschr aube/Ü berl astsicher ung der Nadelschwinge / Scherschraube Bil d all e H S-T ypen auß er 1290 HD P II @ 192\mod_1382077992442_78.docx @ 1637526 @ @ 1

Fig. 28

Pos: 55.55 /BA/Bedienung /Groß packenpresse/Überlastsicherungen / Kuppl ungen / Sternr atsche / Scherschr aube/Ü berl astsicher ung der Nadelschwinge / Scherschraube all e H S-T ypen auß er 1290 HDP II @ 191\mod_1381737358783_78.docx @ 1629117 @ @ 1

Shear screw

The connecting rod (1) of the needle yoke is secured by a shear screw, left-hand side of the

machine.
The shear screw protects the needles and the needle yokes against load peaks.

Pos: 55.56 /Ü berschriften/Ü berschriften 2/P-T/PPick- up @ 55\mod_1292568679348_78.docx @ 521315 @ 2 @ 1

5.9

Pick-up

Pos: 55.57 /BA/Maschi nenbeschr eibung/Maschi nenübersicht/F unktionsweise/Gr oßpackenpr essen/Pick- up Funktionsbeschrei bung Bild 1290 HD P II ohne XC @ 157\mod_1364315127180_78.docx @ 1385997 @ @ 1

Fig. 29
1)

Pick-up

2)

Guide wheel

3)

Spring

4)

Depth limiter

Pos: 55.58 /BA/Maschi nenbeschr eibung/Maschi nenübersicht/F unktionsweise/Gr oßpackenpr essen/Pick- up Funktionsbeschrei bung T 1 bei Ausführung ohne Schnei dwer k @ 168\mod_1367991064915_78.docx @ 1452404 @ @ 1

The pick-up is used to pick up the crop.
The pick-up starts to rotate by turning on the PTO shaft.

Pos: 55.59 /BA/Maschi nenbeschr eibung/Maschi nenübersicht/F unktionsweise/Gr oßpackenpr essenPick-up F unkti onsbeschrei bung T 2 @ 355\mod_1438667690021_78.docx @ 2651025 @ @ 1

The pick-up (1) is raised and lowered via the single-acting control unit (

) on the tractor.

The pick-up is equipped with guide wheels (2). The guide wheels are used to adjust the working

height of the pick-up.
The working height of the pick-up can be manually limited downwards by moving the depth

limiter (4) on both sides of the machine. This makes it possible to drive the machine without

guide wheels with the pick-up in fixed position.
The bearing pressure of the guide wheels can be adjusted to the ground conditions via the

spring (3).

Pos: 55.60 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
60
61
62
63
64
...
»

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов