Krone 870 HDP Скачать руководство пользователя страница 313 | Manualshive

Страница: 313 / 568

Krone 870 HDP Скачать руководство пользователя страница 313

Maintenance - hydraulic system

313

Pos: 105 /Überschriften/Ü berschriften 3/A-E/B/Bordhydr auli k @ 24\mod_1241518305195_78.docx @ 245758 @ 3 @ 1

21.1.1

On-board hydraulic system

Pos: 106 /BA/War tung/U mwel t/Hinweis Entsorgen / Lagern von Öle und Ölfilter U mwelt @ 32 \mod_1253101375171_78.docx @ 311770 @ @ 1

ENVIRONMENT! - Disposal and storage of used lubricants and oil filters

Effect: Environmental damage
Store or dispose used oil and oil filters according to statutory provisions.

Pos: 107 /BA/War tung/Gr oßpackenpr essen/H ydr auli kanlage / Bor dhydr auli k/Bordhydrauli k Öl wechseln Bild 890_1270_1290 @ 193\mod_1382619807192_78.docx @ 1641912 @ @ 1

Fig. 228
1) Dipstick / oil filling hole

2) Hydraulic tank

3) Drain plug

Pos: 108 /BA/War tung/Gr oßpackenpr essen/H ydr auli kanlage / Bor dhydr auli k/Bordhydrauli k Öl wechseln @ 191 \mod_1381903768902_78.docx @ 1633028 @ @ 1

To do this:
•  Stop the machine.
•  Apply the flywheel brake.
•  Open bale channel flaps.

The hydraulic cylinders of the bale channel flaps must be completely retracted.

•  Provide a suitable container for oil change.
•  Unscrew the drain plug.
•  Collect the oil in a suitable container.
•  Screw in drain plug.
•  Screw out dipstick and fill in hydraulic oil.
•  Check the oil level with dipstick.

Pos: 109 /BA/War tung/Öl kontroll e_Wechsel /Ölqualität/Ölmenge: siehe Kapitel T echnische Daten der Maschi ne @ 371 \mod_1441958324612_78.docx @ 2710777 @ @ 1

Oil quality/amount of oil: refer to chapter entitled Technical Data of Machine “Operating

Materials”

Pos: 110 /BA/War tung/Öl kontroll e_Wechsel /Öl kontrolle NEU über Kontrollschraube @ 140\mod_1355141753680_78.docx @ 1244582 @ @ 1

Oil level check:

• Screw out inspection screw.
• Oil level up to control hole.

If the oil reaches the control hole:

• Screw in the inspection screw and tighten it securely.

If the oil does not reach the control hole:

•  Screw out filler plug.
•  Top up oil via oil filling hole until the control hole is reached.
•  Screw in the inspection screw and the filler plug and tighten them securely.

Pos: 111 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
311
312
313
314
315
...
»

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов