Krone 870 HDP Скачать руководство пользователя страница 212 | Manualshive

Страница: 212 / 568

Krone 870 HDP Скачать руководство пользователя страница 212

Terminal – Menus [Medium/Comfort Version Electronics]

212

Pos: 85.305 /Ü berschriften/Ü berschriften 2/A- E/A/Al ar mmel dungen @ 19\mod_1238572457463_78.docx @ 221082 @ 2 @ 1

16.15

Alarm messages

Pos: 85.306 /BA/Info-C enter /WARNUN G-Personen-/M aschinenschäden Nichtbeachtung von Alar men! Ver weis auf Al armmel dungen @ 366\mod_1441112564352_78.docx @ 2689885 @ @ 1

WARNING!

Personal injuries and/or machine damage caused by non-observance of alarm

messages!

When alarm messages are ignored and the malfunction is not remedied, personal injuries

and/or serious damage to the machine could result.
• When alarm message is displayed, remedy the malfunction.

• For possible causes and how to remedy them, refer to chapter entitled “Alarm

Messages”.

• In case the malfunction cannot be remedied, contact KRONE customer service.

Pos: 85.307 /BA/Info-C enter /CCI-ISOBUS-T ermi nal/CCI-Bi G Pack/H auptmenüs/Alar mmeldungenAlar meldung allgemein @ 404\mod_1449052332566_78.docx @ 2870296 @ @ 1

CC000053_2

Fig. 143
The display shows an alarm message if a malfunction occurs on the machine. At the same time

an audio signal will be heard (continuous horn sound). For description, possible cause and

remedy, refer to chapter Terminal - Menus, “Alarms”.

Acknowledging the alarm:

• Press

in order to acknowledge the alarm.

The acoustic signal stops.
If the malfunction occurs again, the alarm message will also appear again.

Pos: 85.308 /BA/Info-C enter /CCI-ISOBUS-T ermi nal/CCI-Bi G Pack/H auptmenüs/Alar mmeldungen/Al ar mmel dung: Beschr eibung der Softkeys @ 267\mod_1400682339813_78.docx @ 2021661 @ @ 1

Softkey

Description

Information

Acknowledge alarm

– The alarm message will appear

again if the malfunction occurs again

Delete message

– This message is not shown until the

operation terminal is started the next

time.

Pos: 85.309 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
210
211
212
213
214
...
»

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов