manualshive.com logo in svg

Krone 870 HDP, Оригинальная инструкция по эксплуатации, Страница: 202 / 568

Поделиться
Скачать
Krone 870 HDP Скачать руководство пользователя страница 202

Terminal – Menus [Medium/Comfort Version Electronics]

 

 

202 

 

Pos: 85.270 /Ü berschriften/Ü berschriften 4/P-T /Sensor B22 „ Ball en auf Schurre“ pr üfen/ei nstellen @ 395\mod_1446619855318_78.docx @ 2815361 @ 4 @ 1 

 

16.14.1.1  Checking/adjusting sensor B22 "Bale on chute" 

Pos: 85.271 /BA/Ei nstellungen/Gr oß packenpr esse/Sensor B22 prüfen/einstellen_Ei nführtext @ 395\mod_1446627404262_78.docx @ 2815714 @  @ 1 

 

Sensor B22 has been preset in the works of the manufacturer. Due to high operational 

demands and component settings, the sensor might have to be adjusted. 

Pos: 85.272 /BA/Ei nstellungen/Gr oß packenpr esse/Sensor B22 prüfen/einstellen_Teil 1 @ 395\mod_1446620104380_78.docx @ 2815392 @  @ 1 

 

1

2

3

4

I

X

5

BPHS0325_1

 

Fig. 133  
•  Press a bale (2) until ¾ of its length have exited the bale channel (1). 
The signal sheet (3) does not cover the sensor (4). The sensor (4) is not alive (there is no iron in 

front of the sensor). 
•  Shut down and safeguard the machine, see chapter Safety, "Shutting down and 

safeguarding the machine". 

•  Check dimension X, measured between the upper edge of the sensor (4) and the edge of 

the signal sheet (3). 

If dimension 

X=5 mm

, the distance of the sensor is correct. 

If dimension 

X is not 5 mm

, adjust the sensor. 

 

Adjustment 

•  Loosen the nuts (5) on both sides of the sensor (4). 
•  Push the sensor (4) upwards until dimension 

X=5 mm

. 

Measured between the upper edge of the sensor (4) and the edge of the signal sheet (3). 
•  Tighten the nuts (5) (tightening torque = 10 Nm). 
•  Use the sensor test to check whether the sensor (4) is still not alive, see Chapter Terminal – 

Menus, "Menu 15-1 'Sensor test'". 

The sensor has been adjusted correctly if the sensor test shows that the sensor is not alive. 
If the sensor test shows that the sensor is alive, adjust the sensor until the sensor test shows 

that the sensor is not alive. 

Pos: 85.273 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов