Krone 870 HDP Скачать руководство пользователя страница 289 | Manualshive

Страница: 289 / 568

Krone 870 HDP Скачать руководство пользователя страница 289

Settings

289

Pos: 93.85.25 /Ü berschriften/Ü berschriften 3/A- E/A/Ausl öseempfi ndlichkei t einstell en @ 107\mod_1334224827926_78.docx @ 964716 @ 3 @ 1

19.16.6

Adjusting the triggering sensitivity

Pos: 93.85.26 /BA/Ei nstellungen/Gr oßpackenpr esse/Variabl es F üllsystem VFS/Bi G PAC K 4x4/Ausl öseempfindlichkei t ei nstellen Bild @ 107\mod_1334224882129_78.docx @ 964744 @ @ 1

Fig. 214

Pos: 93.85.27 /BA/Ei nstellungen/Gr oßpackenpr esse/Variabl es F üllsystem VFS/Bi G PAC K 4x4/Ausl öseempfindlichkei t ei nstellen T ext @ 107\mod_1334224956644_78.docx @ 964772 @ @ 1

The spring (14) is used to adjust the triggering sensitivity of the feeler rocker. When the feeler

rocker has been swung out, the spring pulls the feeler rocker back again (zero position).

The spring length has been preset to C = 205 – 210 mm at the factory.

The higher the spring tension, the more forage is collected in the bale channel chamber.

Note

• Increase the spring tension if the bale channel chamber does not fill up sufficiently

(the filling of the bale upwards must be improved)

• Reduce the spring tension if the overload coupling of the packer responds too

frequently

Increasing / reducing the spring tension:

• Unscrew the screw joint (16).

Reduce dimension C (reduce spring tension)

Increase dimension C (increase spring tension)

• Tighten the screw connection (16)

Pos: 93.85.28 /BA/Ei nstellungen/Gr oßpackenpr esse/Variabl es F üllsystem VFS/Bi G PAC K 4x4/Ausl öseempfindlichkei t Hinweis wann di e T astschwi nge versetzt wer den muss @ 172\mod_1370434630327_78.docx @ 1478555 @ @ 1

hten the screw connection (16)

Note

If the bale shape is still not satisfactory after the spring has been tensioned to the maximum,

install the feeler rocker in the next higher position (see Settings section “Adjusting the feeler

rocker”)
If the overload protection still responds too frequently after the spring tension has been reduced

to the maximum, install the feeler rocker in the next lower position (see Settings section

“Adjusting the feeler rocker”)

Pos: 93.85.29 /BA/Ei nstellungen/Gr oßpackenpr esse/Variabl es F üllsystem VFS/Bi G PAC K 4x4/Ausl öseempfindlichkei t Hinweis " Schlecht ausgefüllte Ball enecken...." @ 172\mod_1370435132973_78.docx @ 1478613 @ @ 1

Note

Poorly filled out bale corners are usually the result of unfavourable swath shapes or

driving to one side.

If the spring tension is too high, the result may be blocking up the packer and thus

reducing throughput.

Pos: 93.85.30 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
287
288
289
290
291
...
»

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов