manualshive.com logo in svg

Krone 870 HDP, Оригинальная инструкция по эксплуатации, Страница: 215 / 568

Поделиться
Скачать
Krone 870 HDP Скачать руководство пользователя страница 215

 

Terminal – Menus [Medium/Comfort Version Electronics]

 

215 

 

Pos: 85.315 /Ü berschriften/Ü berschriften 3/K- O/L/Logische Al arme @ 185\mod_1379419186279_78.docx @ 1594483 @ 3 @ 1 

 

16.15.2 

Logical Alarms  

Pos: 85.316 /BA/Info-C enter /Großpackenpresse/Hauptmenüs/Alar mmeldung en/2) Alar mmeldung en Tabelle allgemein 0 - 9 @ 374\mod_1442555491388_78.docx @ 2723075 @  @ 1 

 

No./symbol 

Possible cause 

Remedy 

0 

 

–  The twine is torn. 
–  The twine end has been reached. 

•  Check the twine and the twine 

tensioner. 

1 

 

–  Blockage in the intake area of the 

packer 

–  The "Packer monitoring" sensor 

has been incorrectly set. 

•  Stop the travelling gear 

immediately. 

•  Reduce the PTO speed until the 

blockage has been removed. 

•  Correctly set the sensor. 

2 

 

–  The force of pressure on the left 

bale channel flap has been 

exceeded. 

In manual mode: 
•  Reduce the target bale channel 

flap pressure. 

In automatic mode: 
•  If the alarm is actuated 

frequently, reduce the target 

force of pressure. 

3 

 

–  The force of pressure on the right 

bale channel flap has been 

exceeded. 

4 

 

–  The knotter is not functioning 

properly. 

–  The "Knotter monitoring" sensor 

has been incorrectly set. 

•  Check the knotter and knotter 

triggering. 

•  Correctly set the sensor. 

5 

 

–  The "Measure" sensor is 

defective or has been incorrectly 

set. 

•  Correctly set the sensor. 

6 

 

–  The "Calibrate" sensor is 

defective or has been incorrectly 

set. 

•  Correctly set the sensor. 

7 

 

–  The flywheel brake is applied. 

•  Release the flywheel brake. 

8 

 

–  The shear screw is torn. 

•  Replace the shear screw. 
•  Check the needles. 
•  Check the swivel range of the 

needles. 

•  Check the twine guide. 

9 

 

–  The bale chute is raised and the 

PTO shaft is rotating. 

•  Lower the bale chute. 

 

Pos: 85.317 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов