Krone 870 HDP Скачать руководство пользователя страница 490

Страница: 490 / 568

Terminal – menus [Medium Plus/Comfort Plus Electronics]

8.16

Alarm messages

Supplement to Operating Instructions 150000774_00 _en

BiG Pack 870 HDP, BiG Pack 870 HDP XC

Error number

Designation

Icon

521104-5

Voltage group (UB5)

521105-5

Voltage group (UB6)

FMI 6: There is a short circuit or ground fault.

Error number

Designation

Icon

521100-6

Voltage group (UB1)

LOW

521101-6

Voltage group (UB2)

521102-6

Voltage group (UB3)

521103-6

Voltage group (UB4)

521104-6

Voltage group (UB5)

521105-6

Voltage group (UB6)

FMI 11: The cause of the error is unknown.

Error number

Designation

Remedy

521106-11

The supply voltage of the sensors could not
be activated.

LOW

8.16.1.5

Logical errors 522000 – 522099

Error number

Possible cause

Remedy

522000-7

During active lubrication no
lubrication flow was detected.

•

Top up grease.

•

Clean the central lubrication.

•

Check the electrical system and
the pump.

522001-7

The flywheel brake is engaged and
the cardan shaft is rotating.

•

Release the flywheel brake.

522002-7

The starting aid is active while the
flywheel brake is engaged.

522003-0

The slip of the tensioning belt on the
cutting rotor is too great.

•

Remove the crop blockage.

•

Set the sensor.

522004-0

>MAX

The pressure on the belt drive for the
cutting rotor is too great.

•

Check the hydraulics.

•

Check the sensor and replace if
required.

522005-2

The cardan shaft rotates in "road
travel" mode.

•

Switch off the PTO shaft.

•

Switch the operating mode

522006-0

ERROR

The cardan shaft is rotating more
quickly than permitted.

•

Reduce cardan shaft speed.

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 870 HDP

Отзывы:

Krone 870 HDP, Оригинальная инструкция по эксплуатации, Страница: 490 / 568

Результаты поиска

Содержание 870 HDP

Отзывы: