Krone 870 HDP Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 568

Krone 870 HDP Скачать руководство пользователя страница 117

Driving and Transport

117

Pos: 81.7 /Überschriften/Überschriften 2/U-Z/VVor bereitung en zur Str aß enfahrt @ 25\mod_1244092605963_78.docx @ 254666 @ 2 @ 1

10.1

Preparations for road travel

Pos: 81.8 /BA/F ahren und Tr ansport/Groß packenpressePrüfen Si e vor der Str aß enfahrt, dass Bi G PAC K 890_1270_1290_4x4 HS @ 325\mod_1425893751195_78.docx @ 2501725 @ @ 1

Before road travel, make certain

–  the PTO shaft is switched off.
–  the machine is fully and correctly hitched to the tractor; refer to chapter “Start-up”.
–  all guards are closed and locked.
–  the retractable ladder is folded in, refer to chapter Machine Description “Ladder”, only for

version 13 tons axle.

–  the bale channel is empty.
–  the flywheel brake is tightened.
–  the pick-up is lifted and secured by the stop cock; refer to chapter Operation “Pick-up”.
–  the bale chute is raised into transport position and secured; refer to chapter Operation

“Raising / Lowering Bale Chute”.

–  the support jack is retracted; refer to chapter Operation “Hydraulic Support Jack”.
–  the parking brake is released; refer to chapter Driving and Transport “Parking Brake”.
–  the control valves on the tractor are in neutral position and locked.
–  the brake is working properly.
–  the lighting works properly, refer to chapter Driving and Transport “Checking Lighting

System”.

– the tyres do not show any cuts or breaks.
– the tyre pressure of the tyres is correct.

Pos: 81.9 /BA/F ahren und Tr ansport/Groß packenpresse/F olgende Arbeitsschritte wer den i n diesem Kapitel beschrieben Fahren und Transport @ 157\mod_1364375905147_78.docx @ 1387035 @ @ 1

The following work steps are described in this chapter:

–  Checking the lighting system.
–  Releasing the parking brake.
–  Handling of the trailing axle, medium electronics or comfort electronics.
–  Moving the machine without hydraulic connection.
–  Moving the machine without connected compressed air brake.
–  Switching off the machine.
–  Applying the parking brake.
–  Fitting wheel chocks.

Pos: 81.10 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
115
116
117
118
119
...
»

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов