Krone 870 HDP Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 568

Krone 870 HDP Скачать руководство пользователя страница 131

KRONE ISOBUS Terminal [Medium/Comfort Version Electronics]

131

Pos: 85.7.1 /Überschriften/Überschriften 2/F-J/IISOBU S Shortcut Button @ 364\mod_1440571658458_78.docx @ 2680236 @ 2 @ 1

11.1

ISOBUS Shortcut Button

Pos: 85.7.2 /BA/Sicherheit/2. Vorangestell te Warnhinweise/Warnung - ISOBU S Shortcut Button @ 364\mod_1440662693340_78.docx @ 2682480 @ @ 1

WARNING!

The ISOBUS Shortcut Button is not an EMERGENCY STOP switch.

If the ISOBUS

Shortcut Button is mistaked for the EMERGENCY STOP switch, there is danger to life.

When actuating the ISOBUS Shortcut Button, activated machine functions are deactivated.

Process oriented procedures are executed until the end. Therefore machine parts may

continue to run after ISOBUS Shortcut Button is actuated. This may lead to injuries.
In no event the ISOBUS Shortcut Button intervenes in tractor functions. This means that

neither the universal shaft function nor the hydraulic function is affected. Therefore the

machine can continue to run after ISOBUS Shortcut Button is actuated. This may lead to

injuries.
• Never use the ISOBUS Shortcut Button as an EMERGENCY STOP switch.

Pos: 85.7.3 /BA/Info-C enter/CC I-ISOBU S-Ter mi nal/M odul e für Bei pack/ISOBU S Short C ut Button/ISOBUS Shortcut Button_wird betätigt_C ompri ma_F orti ma_Ulti ma @ 364\mod_1440576607502_78.docx @ 2680358 @ @ 1

F1

F2

F3

F4

F5

F6

F7

F8

F9

F10

F11

F11

F12

ESC

IBT000055

1

ISB

Fig. 86

When actuating the ISOBUS Shortcut Button (1) of the terminal which is of the pushbutton

design, a stop command is sent to the ISOBUS. This instruction is evaluated by the connected

ISOBUS machine in order to deactivate activated machine functions. Process oriented

procedures are executed until the end.

Actuating ISOBUS Shortcut Button

• Press the ISOBUS Shortcut Button (1).
The above message appears in the display. The job computer blocks all hydraulic functions on

machine side as well as the electronic tying device.

Pos: 85.7.4 /BA/Info-C enter/CC I-ISOBU S-Ter mi nal/M odul e für Bei pack/ISOBU S Short C ut Button/ISOBUS Short Cut Button_F unktion maschinenseitig blocki ert_Bi G Pack HS Baureihe @ 377\mod_1443175725103_78.docx @ 2736723 @ @ 1

The job computer blocks the following functions on the machine side:
•  Start the knotter motor.
•  Start knotter cleaning.
Depending on the machine configuration:
•  Raise/lower the blade bar.
•  Move the bale ejector forwards/backwards.
•  Automatic bale ejection.
•  Raise/lower the bale chute.
•  Switch to MultiBale.

Pos: 85.7.5 /Layout M odule /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
129
130
131
132
133
...
»

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов