Krone 870 HDP Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 568

Krone 870 HDP Скачать руководство пользователя страница 29

Safety

29

Pos: 19.73 /BA/Sicherheit/1. Grundlegende Sicherheitshinweise/Gefahr en bei best. Tätigkeiten: Gefahr durch Schweißar beiten - Außer Selbstfahr er @ 244\mod_1395756512013_78.docx @ 1907210 @ @ 1

Danger associated with welding work

Improper welding work will endanger the operational safety of the machine. As a result,

accidents may occur and people may be seriously injured or killed.
• Before performing welding work on the machine, obtain the consent of KRONE customer

service and, if required, identify alternatives.

• Have welding work performed by experienced technicians only.

Pos: 19.74 /Ü berschriften/Ü berschriften 3/F-J/GGefahren bei besti mmten T ätig keiten: Arbeiten an R äder n und R eifen @ 187\mod_1380023183993_78.docx @ 1607653 @ 3 @ 1

3.4.20

Dangers associated with certain activities: Working on wheels and tyres

Pos: 19.75 /BA/Sicherheit/1. Grundlegende Sicherheitshinweise/Gefahr en bei best. Tätigkeiten: Arbeiten an R ädern und Rei fen @ 177\mod_1373290205171_78.docx @ 1510669 @ @ 1

Fitting/removing wheels and tyres

Improper fitting or removal will endanger operational safety. As a result, accidents may occur

and people may be seriously injured or killed.

The fitting of wheels and tyres requires adequate knowledge and approved tools.
• If there is a lack of knowledge, have the wheels and tyres fitted by the KRONE dealer or by

a qualified tyre service.

• When fitting tyres on the wheel rims, never exceed the maximum permitted pressure

specified by the tyre manufacturers, otherwise the tyre or even the wheel rim may explode.

• When fitting the wheels, tighten the wheel nuts to the stipulated torque, see chapter

Maintenance "Tyres".

Pos: 19.76 /Ü berschriften/Ü berschriften 3/U-Z/Verhalten i n Gefahrensituationen und bei U nfällen @ 187\mod_1380023393504_78.docx @ 1607682 @ 3 @ 1

3.4.21

Behaviour in hazardous situations and when accidents occur

Pos: 19.77 /BA/Sicherheit/1. Grundlegende Sicherheitshinweise/Verhalten in Gefahr ensi tuati onen und bei Unfällen @ 177\mod_1373291508723_78.docx @ 1510758 @ @ 1

Neglected or incorrect procedures in hazardous situations may obstruct or prevent the rescue of

people in danger. Difficult rescue conditions will impair the chances of helping and healing the

injured.
•  In principle: Switch off the machine.
•  Gain an overview of the hazardous situation and identify the cause of the hazard.
•  Safeguard the accident location.
•  Rescue people from the danger zone.
•  Withdraw from the danger zone and do not enter again.
•  Alert rescue teams and, if possible, fetch help.
•  Take immediate life-saving measures.

Pos: 20 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
27
28
29
30
31
...
»

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов