Krone 870 HDP Скачать руководство пользователя страница 272 | Manualshive

Страница: 272 / 568

Krone 870 HDP Скачать руководство пользователя страница 272

Settings

272

Pos: 93.80 /BA/Ei nstellungen/Groß packenpresse/Knoter/Inbetriebnahme Knoter @ 24\mod_1241083585365_78.docx @ 242950 @ 3 @ 1

19.13.2

Start-up

The knotter has been set and tested by the manufacturer. It should work properly without

requiring any further settings. If there are problems with tying when it is placed in service for the

first time, the mechanisms should not be set immediately, since this is usually caused by errors

that are caused by paint, rust and bare spots. It is recommended to remove the rust protection

grease from the twine retainer and knotter before start-up.

Pos: 93.81.1 /Ü berschriften/Ü berschriften 3/A-E/D /Doppel knoter @ 24\mod_1241099544678_78.docx @ 243310 @ 3 @ 1

19.13.3

Double knotter

Pos: 93.81.2 /Ü berschriften/Ü berschriften 3/K-O/KKnüpfer hakens einstell en @ 156\mod_1363867882250_78.docx @ 1378155 @ 3 @ 1

19.13.4

Setting the Knotter Hook

Pos: 93.81.3 /BA/Ei nstellungen/Groß packenpresse/Knoter/D oppel knoter/Knüpferhaken D oppel knoter Bild 1290 HD P II @ 156\mod_1363864056928_78.docx @ 1377963 @ @ 1

Fig. 194

Pos: 93.81.4 /BA/Ei nstellungen/Groß packenpresse/Knoter/D oppel knoter/Knüpferhaken einstellen @ 156\mod_1363864342258_78.docx @ 1378122 @ @ 1

The knotter tongue (2) of the knotter hook is tensioned by the closer (1).

If the clamping effect on the knotter tongue is too great, the knot will be left hanging on

the knotter tongue. The twine strand will tear.

If there is not enough clamping effect on the knotter tongue, either no knot or a loose

knot will form.

Set the clamping effect.

Reducing the clamping effect:

• Unscrew nut (4) on the closer by approx. 30°.

Increasing clamping effect:

• Unscrew nut (4) on the closer by approx. 30°.

Note

The knotter tongue needs a slight minimum tension. Therefore the clamping effect must never

be loosened completely.

Pos: 93.81.5 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
270
271
272
273
274
...
»

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов