manualshive.com logo in svg

Krone 870 HDP, Оригинальная инструкция по эксплуатации, Страница: 224 / 568

Поделиться
Скачать
Krone 870 HDP Скачать руководство пользователя страница 224

Operation

 

 

224 

 

Pos: 87 /Layout M odul e /Di ese Seite ist bewusst freig elassen worden. @ 1\mod_1201783680373_78.docx @ 54443 @  @ 1 

Pos: 89.1 /Überschriften/Überschriften 1/A-E/Bedienung @ 0\mod_1199789505403_78.docx @ 34825 @ 1 @ 1 

 

18 

Operation  

Pos: 89.2 /BA/Sicher heit/2. Vor angestellte Warnhi nweise/WARNUNG -  Nichtbeachtung der grundl egenden Sicherheitshinweise alte F orm @ 254\mod_1397485793575_78.docx @ 1953347 @  @ 1 

 

 

WARNING! 

If the basic safety instructions are not followed, people may be seriously injured or 

killed.  

•  To avoid accidents, the basic safety instructions in the chapter Safety must have been 

read and followed, see chapter Safety "Basic safety instructions". 

 

Pos: 89.3 /BA/Sicher heit/2. Vor angestellte Warnhi nweise/WARNUNG -  Nichtbeachtung der Sicherheitsr outinen al te For m @ 273\mod_1404117435996_78.docx @ 2058712 @  @ 1 

 

 

WARNING! 

If the safety routines are not adhered to, people may be seriously injured or killed.  

•  To avoid accidents, the safety routines in the chapter Safety must be read and followed, 

see chapter Safety "Safety routines". 

 

Pos: 89.4 /BA/Sicher heit/2. Vor angestellte Warnhi nweise/Achtung - Pressvorgang mit maxi mal em Dr uck g estartet - ALT E F ORM @ 362\mod_1439815983709_78.docx @ 2671856 @  @ 1 

 

 

ATTENTION! – Machine may be damaged if the baling process is started at maximum 

baling pressure. 

If the baling process is started at maximum baling pressure, the friction clutch on the flywheel 

may be damaged. 
•  Do not start the baling process at maximum baling pressure. 

 

Pos: 89.5 /BA/Bedi enung /Gr oßpackenpr essePr essen vor ber eiten @ 325\mod_1425894223332_78.docx @ 2501756 @ 2 @ 1 

 

18.1 

Preparation for baling 

 

Before you start baling, check to make certain 

–  the bale ejector is in the front position. 
–  the bale brake is locked. 
–  the tying twine reserves are adequate. 
–  the correct cutting length is set, for the cutting system version. 
–  the working height of the pick-up is set. 
–  the correct bale length is set via the terminal. 
–  the knotter shaft is unlocked as otherwise an endless bale will be pressed. 
–  the flywheel brake is released. 
 
•  Lower bale chute into working position. 
•  Lower pick-up into working position. 
•  Set bale length and baling pressure via terminal. 
 

Pos: 89.6 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @  @ 1 

Содержание 870 HDP

























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов