manualshive.com logo in svg

Intel Embedded Intel486, Справочник по аппаратуре

Продукт Intel Embedded Intel486 - устройство с высокой производительностью для встраиваемых систем. Для подробной информации о его функциях и использовании скачайте бесплатное Hardware Reference Manual с нашего сайта. Идеальный инструмент для раскрытия потенциала вашего устройства. (Website) - ваш лучший источник для скачивания.

Поделиться
Скачать
background image

10-39

PHYSICAL DESIGN AND SYSTEM DEBUGGING

The Intel486 processor starts executing instructions at location FFFFFFF0H after reset. 
The address latch is connected and the address is verified. 

4.

The PAL implementing the address decoder should be connected to the Intel486 
processor.

10.8.1 Debugging Features of the Intel486™ Processor 

The Intel486 processor provides several features which simplify the debugging process for the
system hardware designer. The device offers three on-chip debugging aids: 

•

The code execution breakpoint opcode. 

•

The single-step capability provided by the TF bit in the flag register. 

•

The code and data breakpoint capability as provided by the debug registers (DR3–DR0, 
DR6 and DR7). 

10.8.2 Breakpoint Instruction 

The Intel486 processor provides a breakpoint instruction that can be used by software debuggers.
This instruction is a single byte opcode and generates an exception 3 trap when it is executed. In
a typical environment a debugger program can place the breakpoint instruction at various points
in the program. The single-byte breakpoint opcode is an alias for the two-byte general software
interrupt instruction, INTn where n=3. The only difference between INT 3 and INT n is that INT3
is never IOPL-sensitive but INTn is IOPL-sensitive in Protected Mode and Virtual 8086 Mode. 

10.8.3 Single-Step Trap 

The Intel486 processor supports x86-compatible single-step feature. If the single stepflag bit
(bit 8, TF) is set to 1 in the EFLAG register, a single step exception occurs. This exception is auto-
vectored to exception 1 and occurs immediately after completion of the next instruction. Typical-
ly a debugger sets the TF bit of the EFLAG register on the debugger's stack followed by transfer
of the control to the user program. The debugger also loads the flag image (EFLAG) via the IRET
instruction. The single-step trap occurs after execution of one instruction of the user program. 

Since the exception 1 occurs right after the execution of the instruction as a trap, the CS:EIP
pushed onto the debugger's stack points to the next unexecuted instruction of the program which
is being debugged, merely by ending with an IRET instruction. 

After MOV to SS and POP to SS instructions, the Intel486 processor masks some exceptions, in-
cluding single-step trap exceptions. Refer to the “Exceptions and Interrupts” chapter in the
Intel486™ Processor Family Programmer’s Reference Manual for an explanation of this pro-
cess.

10.8.4 Debug Registers 

The Intel486 processor has an advanced debugging feature. It has six debug registers that allow
data access breakpoints as well code access breakpoints. Since the breakpoints are indicated by

Содержание Embedded Intel486















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Embedded Intel486

Oracle Talari E1000 Installation Manual preview
Talari E1000
Бренд: Oracle Страницы: 24
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Бренд: ADTRAN Страницы: 2
Supersonic Franky Instruction Manual preview
Franky
Бренд: Supersonic Страницы: 46
Cabletron Systems MMAC-Plus 9G536-04 User Manual preview
MMAC-Plus 9G536-04
Бренд: Cabletron Systems Страницы: 42
Atmel STK501 Specification Sheet preview
STK501
Бренд: Atmel Страницы: 2
Billion BiPAC 5200S RC Series User Manual preview
BiPAC 5200S RC Series
Бренд: Billion Страницы: 79
Quadram Quadboard Operation Manual preview
Quadboard
Бренд: Quadram Страницы: 21
RR-Concepts StationMaster Manual preview
StationMaster
Бренд: RR-Concepts Страницы: 12
Omron G3RV-SL500-A Manual preview
G3RV-SL500-A
Бренд: Omron Страницы: 14
Ceragon Fibe-Air IP-10G Installation Manual preview
Fibe-Air IP-10G
Бренд: Ceragon Страницы: 71
Enterasys GPIM-08 Reference Sheet preview
GPIM-08
Бренд: Enterasys Страницы: 2
V7 SCREENSHARE PRO User Manual preview
SCREENSHARE PRO
Бренд: V7 Страницы: 4
ICP DAS USA ZT-2005-C8 User Manual preview
ZT-2005-C8
Бренд: ICP DAS USA Страницы: 60
Motorola MC68VZ328 User Manual preview
MC68VZ328
Бренд: Motorola Страницы: 376
Motorola MC68341 User Manual preview
MC68341
Бренд: Motorola Страницы: 20
Citizen IF1-ET01 User Manual preview
IF1-ET01
Бренд: Citizen Страницы: 26
Renesas M38C29T-64LCA User Manual preview
M38C29T-64LCA
Бренд: Renesas Страницы: 6
iSMA CONTROLLI SfAR-S-8TO User Manual preview
SfAR-S-8TO
Бренд: iSMA CONTROLLI Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды