Intel Embedded Intel486 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 334

background image

EMBEDDED Intel486™ PROCESSOR HARDWARE REFERENCE MANUAL

1-4

Register Bits

When the text refers to more that one bit, the range of bits is represented
by the highest and lowest numbered bits, separated by a long dash
(example: A15–A8). The first bit shown (15 in the example) is the most-
significant bit and the second bit shown (8) is the least-significant bit.

Register Names

Register names are shown in uppercase. If a register name contains a
lowercase italic character, it represents more than one register. For
example, PnCFG represents three registers: P1CFG, P2CFG, and P3CFG.

Signal Names

Signal names are shown in uppercase. When several signals share a
common name, an individual signal is represented by the signal name
followed by a number, while the group is represented by the signal name
followed by a variable (n). For example, the lower chip-select signals are
named CS0#, CS1#, CS2#, and so on; they are collectively called CSn#.
A pound symbol (#) appended to a signal name identifies an active-low
signal. Port pins are represented by the port abbreviation, a period, and
the pin number (e.g., P1.0, P1.1).

1.3

SPECIAL TERMINOLOGY

The following terms have special meanings in this manual.

Assert and Deassert

The terms assert and deassert refer to the acts of making a signal
active and inactive, respectively. The active polarity (high/low) is
defined by the signal name. Active-low signals are designated by the
pound symbol (#) suffix; active-high signals have no suffix. To
assert RD# is to drive it low; to assert HOLD is to drive it high; to
deassert RD# is to drive it high; to deassert HOLD is to drive it low.

DOS I/O Address

Peripherals that are compatible with PC/AT system architecture can
be mapped into DOS (or PC/AT) addresses 0H–03FFH. In this
manual, the terms DOS address and PC/AT address are synonymous.

Expanded I/O Address

All peripheral registers reside at I/O addresses 0F000H–0FFFFH.
PC/AT-compatible integrated peripherals can also be mapped into
DOS (or PC/AT) address space (0H–03FFH).

PC/AT Address

Integrated peripherals that are compatible with PC/AT system
architecture can be mapped into PC/AT (or DOS) addresses 0H–
03FFH. In this manual, the terms DOS address and PC/AT address
are synonymous.

Set and Clear

The terms set and clear refer to the value of a bit or the act of giving
it a value. If a bit is set, its value is “1”; setting a bit gives it a “1”
value. If a bit is clear, its value is “0”; clearing a bit gives it a “0”
value.

«
...
20
21
22
23
24
...
»

Содержание Embedded Intel486















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Embedded Intel486

Бренд: ZALMAN Страницы: 20

Бренд: dbx Страницы: 2

Бренд: ICP DAS USA Страницы: 8

Бренд: Raritan Страницы: 4

Бренд: Yaesu Страницы: 2

Бренд: Clavister Страницы: 89

F-Tile SDI II Intel Agilex

Бренд: Intel Страницы: 39

Бренд: ebm-papst Страницы: 11

Бренд: YASKAWA Страницы: 15

Бренд: DAD Страницы: 16

Бренд: Addonics Technologies Страницы: 1

Бренд: Z-Wave Страницы: 6

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Бренд: Intel Страницы: 86

Бренд: C&T Solution Страницы: 129

Бренд: Paradyne Страницы: 6

Бренд: EMTRUST Страницы: 103

Бренд: Network Critical Страницы: 200

Бренд: LevelOne Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды