manualshive.com logo in svg

Intel Embedded Intel486, Справочник по аппаратуре

Продукт Intel Embedded Intel486 - устройство с высокой производительностью для встраиваемых систем. Для подробной информации о его функциях и использовании скачайте бесплатное Hardware Reference Manual с нашего сайта. Идеальный инструмент для раскрытия потенциала вашего устройства. (Website) - ваш лучший источник для скачивания.

Поделиться
Скачать
background image

8-25

SYSTEM BUS DESIGN

resistors or by driving these lines low when HLDA is asserted. A17–A2 are also used for system
controller/ISA bridge link interface transfers. These signals are 3-stated after a hard reset.

The Byte Enable signals BE3#–BE0# indicate active bytes during read and write cycles. These
signals are 3-stated after a hard reset.

Host Data HD3–HD0 are connected to the host CPU data bus. These signals are inputs after a
hard reset.

The Host Data Parity signals, HPD3–HPD0, are bi-directional parity signals for the host data bus.
These signals provide parity to the system controller during main memory read cycles. The sys-
tem controller sends parity information to main memory during non-CPU main memory write cy-
cles. These signals are 3-stated after a hard reset.

Bus Cycle Definition, M/IO#, D/C# and W/R#, are signals that define the Host bus cycle. M/IO#
is a bi-directional signal that distinguishes between memory and I/O cycles. D/C# is a bi-direc-
tional signal that differentiates between data and control cycles. W/R# is a bi-directional signal
that distinguishes between read and write cycles. Note that special cycles are identified by BE3#–
BE0# and A4–A2. These signals are 3-stated after a hard reset.

Page Cache Disable/Cache, PCD/CACHE#, is a multiplexed signal pin with two functions, de-
pending on the type of CPU used. The PCD cache input signal, when asserted, indicates the cur-
rent cycle cannot be cached in the L2 cache during line fill operation. When PCD is asserted, the
line is not cached in L1 or L2. The CACHE# signal is active along with the first ADS# until the
first RDY# or BRDY#. For line fills, the functionality of the CACHE# signal is identical to that
of the PCD signal. During write-back cycles, CACHE# is always asserted at the beginning of the
line write-back. The beginning of a write-back cycle is uniquely identified by active ADS#, W/R#
and CACHE#. Beginning of the snoop write-back is identified by the ADS#, W/R#, CACHE#
and HITM# being active.

The Address Status, ADS#, input indicates that the bus cycle definition signals (M/IO#, D/C#,
W/R#), BE3#–BE0#, and A31–A30, A26–A2 are available on their corresponding pins.

Ready, RDY#, indicates that the current non-burst bus cycle is complete. This signal is deasserted
after a hard reset.

Burst Ready, BRDY#, performs the same function during a burst cycle that RDY# performs dur-
ing a non-burst cycle. This signal is deasserted after hard reset.

Burst Last, BLAST#, indicates the end of a burst access for CPU-initiated cycles.

The system controller asserts HOLD to the CPU to request ownership of the Host bus. This signal
is deasserted after a hard reset.

Hold Acknowledge, HLDA, must be asserted by the CPU for the system controller to grant a new
master on the PCI or ISA buses. When HLDA is deasserted, the CPU is the Host bus master and
the system controller is the PCI bus master. When HLDA is deasserted, the system controller is
also the master on the system controller/ISA bridge link interface.

Address Hold, AHOLD, output signal forces the CPU to float its address bus in the next clock.
The system controller asserts this signal in preparation to perform a system controller/ISA bridge
interface transfer, when SRESET needs to be asserted, or upon Deturbo logic requests. This sig-
nal is deasserted after a hard reset.

Содержание Embedded Intel486















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Embedded Intel486

Barco EX Safety Manual preview
EX
Бренд: Barco Страницы: 100
A10 Thunder Series Manual preview
Thunder Series
Бренд: A10 Страницы: 52
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Бренд: 3Com Страницы: 204
Teagle Tomahawk 7100 Operator'S Manual preview
Tomahawk 7100
Бренд: Teagle Страницы: 40
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Бренд: IEI Technology Страницы: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Бренд: Dahua Technology Страницы: 14
Cypress Semiconductor CY7C1329H Specification Sheet preview
CY7C1329H
Бренд: Cypress Semiconductor Страницы: 16
Aqua Computer Aquaduct 240 eco Operating And Assembly Manual preview
Aquaduct 240 eco
Бренд: Aqua Computer Страницы: 20
ADS Technologies API-800 Installation Manual preview
API-800
Бренд: ADS Technologies Страницы: 21
Lattice Semiconductor LatticeMico GPIO Manual preview
LatticeMico GPIO
Бренд: Lattice Semiconductor Страницы: 28
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Бренд: Radica Games Страницы: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Бренд: Airvana Страницы: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Бренд: Renesas Страницы: 8
Digi 9P 9360/9750 User Manual preview
9P 9360/9750
Бренд: Digi Страницы: 75
Optus Ultra WiFi Booster Quick Manual preview
Ultra WiFi Booster
Бренд: Optus Страницы: 8
Idis DR-8364F Quick Manual preview
DR-8364F
Бренд: Idis Страницы: 16
H3C SecPath F50X0 Series Manual preview
SecPath F50X0 Series
Бренд: H3C Страницы: 41
PairGain 150-2230-01 Quick Installation Manual preview
150-2230-01
Бренд: PairGain Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды