Intel Embedded Intel486 Скачать руководство пользователя страница 205 | Manualshive

Страница: 205 / 334

background image

7-33

PERIPHERAL SUBSYSTEM

Figure 7-18. Timing of a Posted Write

7.4

DIFFERENCE BETWEEN THE Intel486 DX PROCESSOR FAMILY AND
Intel386 PROCESSORS

The IntelDX2 and IntelDX4 processors are integrated chips that is include a CPU, a math copro-
cessor, and a cache controller. It is fully compatible with its predecessor, the Intel386 DX pro-
cessor, yet has the following differences:

•

Intel486 processor offers dynamic bus sizing to support 8-, 16-, and 32-bit bus sizes, except
for the Ultra-Low Power Intel486 GX processor, which supports a 16-bit data bus only.
Dynamic bus sizing requires external swapping logic. The Intel386 DX processor supports
only 16-bit and 32-bit bus sizes and does not require swapping logic.

•

The Intel486 processor has a burst transfer mode which can transfer four 32-bit words from
external memory to the on-chip cache using only five clock cycles. The Intel386 DX
processor requires at least eight clock cycles to transfer the same amount of data.

•

The Intel486 processor has a BREQ output which supports multi-processor environments.

•

The Intel486 processor’s bus is significantly faster than the Intel386 processor’s bus. New
features include a 1x clock, parity support

†

, burst cycles, cacheable cycles, cache invalidate

cycles and 8-bit support. The Hardware Interface and Bus Operation chapters of the
Embedded Intel486™ Processor Family Developer’s Manual explains of the bus
functionality and its hardware interface.

•

To support the on-chip cache, new bits have been added to control register 0 (CD and NW),
new pins have been added to the bus, and new bus cycle types have been added. The on-
chip cache must be enabled after reset by clearing the CD and NW bit in CR0.

†

Not available in the ULP486SX or ULP486GX processors.

CLK

T1

T1

T2

T2

ADS

CPU

Latched

RDX#

Address

Address

Cycle 1

Cycle 1

Cycle 2

«
...
203
204
205
206
207
...
»

Содержание Embedded Intel486















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Embedded Intel486

EK-FB GA AX370 Gaming RGB Monoblock

Бренд: ekwb Страницы: 2

Parallel & Serial Port Checker PPC

Бренд: B&B Electronics Страницы: 4

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

Бренд: Kaptia Страницы: 14

Бренд: Arbor Technology Страницы: 8

CNPS5X PERFORMA

Бренд: ZALMAN Страницы: 8

Бренд: Symantec Страницы: 100

Бренд: mikroElektronika Страницы: 2

Бренд: Cypress Semiconductor Страницы: 19

Бренд: National Instruments Страницы: 121

Бренд: Xilinx Страницы: 29

Бренд: H3C Страницы: 34

X-FireWire Card

Бренд: Apogee Страницы: 32

Бренд: Xilinx Страницы: 43

ACC-BKT-AX-BEAM

Бренд: Extreme Networks Страницы: 35

Бренд: ZyXEL Communications Страницы: 263

Бренд: IBASE Technology Страницы: 49

Бренд: Xaoc Devices Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды