Infineon XC886CLM Скачать руководство пользователя страница 494 | Manualshive

Страница: 494 / 663

background image

XC886/888CLM

Controller Area Network (MultiCAN) Controller

User’s Manual

15-50

V1.3, 2010-02

MultiCAN, V1.0

02

H

Argument:

List Index

Argument:

Message
Object
Number

Static Allocate

Allocate message object to a list. The
message object is removed from the list
that it currently belongs to and appended
to the end of the list given by PANAR2.
This command is also used to deallocate
a message object. In this case, the target
list is the list of unallocated elements
(PANAR2 = 0).

03

H

Argument:

List Index

Result:

Bit 7: ERR
Bit 6-0: undefined

Result:

Message
Object
Number

Dynamic Allocate

Allocate the first message object of the
list of unallocated objects to the selected
list. The message object is appended to
the end of the list. The message number
of the message object is returned in
PANAR1.
An ERR bit (bit 7 of PANAR2) reports the
success of the operation:
0

Success.

1

The operation has not been
performed because the list of
unallocated elements was empty.

04

H

Argument:

Destination Object
Number

Argument:

Source
Object
Number

Static Insert Before

Remove a message object (source
object) from the list that it currently
belongs to and insert it before a given
destination object into the list structure of
the destination object.
The source object thus becomes the
predecessor of the destination object.

Table 15-7

Panel Commands

(cont’d)

PANCMD PANAR2

PANAR1

Command Description

*

«
...
492
493
494
495
496
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: Vacon Страницы: 64

Бренд: Fantech Страницы: 2

Бренд: Radware Страницы: 98

Бренд: National Instruments Страницы: 72

Бренд: POLA Страницы: 2

Бренд: OJ Electronics Страницы: 8

SensoTimer ST6 Duo eco!ogic

Бренд: Kärcher Страницы: 96

Бренд: Digiplex Страницы: 48

Бренд: Vexve Страницы: 24

Бренд: Xinje Страницы: 41

SYG-S7G2-43C-MDK

Бренд: FDI Страницы: 28

Бренд: ViziT Страницы: 6

IC 912 LX Pt100 R

Бренд: Eliwell Страницы: 8

MAXinBOX FANCOIL 2CH2P

Бренд: Zennio Страницы: 2

Бренд: DMC Страницы: 12

Бренд: AirCom Страницы: 4

emotion MT2-11A

Бренд: Saci Pumps Страницы: 262

Бренд: MKS Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды