Infineon XC886CLM Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 663

background image

XC886/888CLM

Introduction

User’s Manual

1-19

V1.3, 2010-02

Introduction, V 1.1

1.6

Reserved, Undefined and Unimplemented Terminology

In tables where register bit fields are defined, the following conventions are used to
indicate undefined and unimplemented function. Further, types of bits and bit fields are
defined using the abbreviations shown in

1.7

Acronyms

lists the acronyms used in this document.

Table 1-4

Bit Function Terminology

Function of Bits

Description

Unimplemented

Register bit fields named “0” indicate unimplemented functions
with the following behavior.
Reading these bit fields returns 0.
Writing to these bit fields has no effect.
These bit fields are reserved. When writing, software should
always set such bit fields to 0 in order to preserve compatibility
with future products. Setting the bit fields to 1 may lead to
unpredictable results.

Undefined

Certain bit combinations in a bit field can be labeled “Reserved”,
indicating that the behavior of the XC886/888 is undefined for
that combination of bits. Setting the register to undefined bit
combinations may lead to unpredictable results. Such bit
combinations are reserved. When writing, software must always
set such bit fields to legal values as provided in the bit field
description tables.

rw

The bit or bit field can be read and written.

r

The bit or bit field can only be read (read-only).

w

The bit or bit field can only be written (write-only). Reading
always return 0.

h

The bit or bit field can also be modified by hardware (such as a
status bit). This attribute can be combined with ‘rw’ or ‘r’ bits to
‘rwh’ and ‘rh’ bits, respectively.

Table 1-5

Acronyms

Acronym

Description

ADC

Analog-to-Digital Converter

ALU

Arithmetic/Logic Unit

BSL

BootStrap Loader

*

«
...
31
32
33
34
35
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: BADODOSECURITY Страницы: 8

Бренд: Maestra Страницы: 22

Бренд: National Instruments Страницы: 6

Бренд: Atari Страницы: 3

Бренд: Dungs Страницы: 56

Бренд: Emec Страницы: 8

Бренд: phytron Страницы: 55

Бренд: OLYS Страницы: 4

The Boost Box WS 1107

Бренд: Watersports Innovations Страницы: 12

Бренд: Parker Страницы: 31

Synergy SGY-101

Бренд: Fairford Страницы: 20

Бренд: ST Страницы: 40

Бренд: Varian Страницы: 37

Бренд: NCE Страницы: 4

AMP 3K/40 CE 2161600-1

Бренд: TE Connectivity Страницы: 29

Бренд: QSC Страницы: 13

Бренд: GAC Страницы: 4

Бренд: ICP DAS USA Страницы: 153

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды