Infineon XC886CLM Скачать руководство пользователя страница 611 | Manualshive

Страница: 611 / 663

background image

XC886/888CLM

On-Chip Debug Support

User’s Manual

17-4

V1.3, 2010-02

OCDS, V 1.0

17.3.1.1

Hardware Breakpoints

Hardware breakpoints are generated by observing certain address buses within the
XC886/888 system. The bus relevant to the hardware breakpoint type is continuously
compared against certain registers where addresses for the breakpoints have been
programmed.

The hardware breakpoints can be classified into different types:

•

Depending on the address bus supervised
–

Breakpoints on Instruction Address

Program Memory Address (PROGA) is observed

–

Breakpoints on IRAM Address

Internal Data Memory Addresses for read/write (SOURCE_A, DESTIN_A) are
observed

•

Depending on the way comparison is done
– Equal breakpoints

Comparison is done only against one value; the break event is raised when just
this value is matched.

– Range breakpoints

Comparison is done against two values; the break event is raised when a value
observed is found belonging to the range between two programmed values
(inclusively).

Breakpoints on Instruction Address

These Instruction Pointer (IP) breakpoints are generated when a break address is
matched for the first byte of an instruction that is going to be executed i.e., for the
address within Program Memory where an instruction opcode is fetched from.

Note: In case of 2- and 3-byte instructions, the break will not be generated for addresses

of the second and third instruction bytes.

The IP breakpoints are of Break Before Make type, therefore the instruction at the
breakpoint is executed only after the proper debug action is taken.

The OCDS in XC886/888 supports both equal breakpoints and range breakpoints on
Instruction address (see

“Configurations of Hardware Breakpoints” on Page 17-5

).

Breakpoints on IRAM Address

These breakpoints are generated when an instruction performs read or write access to
a location within a defined address range from the Internal Data Memory (IRAM).

The IRAM breakpoints are of Break After Make type, therefore the proper debug action
is taken immediately after the operation to the breakpoint address is performed.

The OCDS in XC886/888 supports only range breakpoints on IRAM address.

*

«
...
609
610
611
612
613
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: ABB Страницы: 128

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

MicroTech II UV05

Бренд: AAF Страницы: 50

Бренд: Cypress Semiconductor Страницы: 36

Бренд: DAYLIFF Страницы: 40

Бренд: Progeny Страницы: 4

Бренд: Vector Страницы: 22

Бренд: TAC Vista Страницы: 2

Бренд: Ellard Страницы: 21

Бренд: Aurora Scientific Страницы: 21

Бренд: Clare Controls Страницы: 3

Бренд: Swegon Страницы: 11

Kaysun KC-03.2 SPS

Бренд: Frigicoll Страницы: 44

Бренд: Zonet Страницы: 2

Бренд: Intrinsyc Страницы: 38

Бренд: Omron Страницы: 157

Бренд: Teracom Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды