Infineon XC886CLM Скачать руководство пользователя страница 458 | Manualshive

Страница: 458 / 663

background image

XC886/888CLM

Controller Area Network (MultiCAN) Controller

User’s Manual

15-14

V1.3, 2010-02

MultiCAN, V1.0

has no successor (in the example object 3 is the last message object in the list, indicated
by PNEXT = 3).

Bit field MOCTRn.LIST indicates the list index number to which the message object is
currently allocated. The message object of the example are allocated to list 2. Therefore,
all LIST bit fields for the message objects assigned to list 2 are set to LIST = 2.

15.1.4.2

List of Unallocated Elements

The list with list index 0 has a special meaning: it is the list of all unallocated elements.
An element is called unallocated if it belongs to list 0 (MOCTRn.LIST = 0). It is called
allocated if it belongs to a list with an index not equal to 0 (MOCTRn.LIST > 0).

After reset, all message objects are unallocated. This means that they are assigned to
the list of unallocated elements with MOCTRn.LIST = 0. After this initial allocation of the
message objects caused by reset, the list of all unallocated message objects is ordered
by message number (predecessor of message object n is object n-1, successor of object
n is object n+1).

15.1.4.3

Connection to the CAN Nodes

Each CAN node is linked to one unique list of message objects. A CAN node performs
message transfer only with the message objects that are allocated to the list of the CAN
node. This is illustrated in

Figure 15-7

. Frames that are received on a CAN node may

only be stored in one of the message objects that belongs to the CAN node; frames to
be transmitted on a CAN node are selected only from the message objects that are
allocated to that node, as indicated by the vertical arrows.

There are more lists (eight) than CAN nodes (two). This means that some lists are not
linked to one of the CAN nodes. A message object that is allocated to one of these
unlinked lists cannot receive messages directly from a CAN node and it may not transmit
messages.

FIFO and gateway mechanisms refer to message object numbers and not directly to a
specific list. The user must take care that the message objects targeted by
FIFO/gateway belong to the desired list. The mechanisms allow working with lists that
do not belong to this CAN node.

*

«
...
456
457
458
459
460
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: Parker Страницы: 30

Бренд: Zolix Instruments Страницы: 22

Бренд: Bard Страницы: 8

Бренд: L-Acoustics Страницы: 20

Бренд: National Instruments Страницы: 34

Бренд: Click2Enter Страницы: 34

Бренд: Rabbit Страницы: 12

Бренд: bluelab Страницы: 39

Бренд: Digiplex Страницы: 48

Бренд: D+H Страницы: 16

Бренд: CompuPro Страницы: 33

Бренд: Levven Страницы: 2

Бренд: MAKELSAN Страницы: 28

Hydromat DP DN 20

Бренд: oventrop Страницы: 40

Бренд: Icom Страницы: 23

Triton UltraLift

Бренд: HydroHoist Страницы: 9

Бренд: YOKOGAWA Страницы: 12

Бренд: Baldor Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды