manualshive.com logo in svg

Infineon XC886CLM, Руководство пользователя

Infineon XC886CLM - микроконтроллер с высокой производительностью для широкого спектра применений. Пользователи могут скачать руководство пользователя бесплатно на manualshive.com, чтобы узнать больше о функциях и настройках этого продукта. Управляйте своими проектами с легкостью, благодаря нашему подробному руководству.

Поделиться
Скачать
background image

XC886/888CLM

Interrupt System

 

User’s Manual

5-32

V1.3, 2010-02

Interrupt System, V 1.0

 

5.6.4

Interrupt Priority Registers

Each interrupt source can be individually programmed to one of the four available priority
levels. Two pairs of interrupt priority registers are available to program the priority level
of each interrupt vector. The first pair of Interrupt Priority Registers are SFRs IP and IPH.
The second pair of Interrupt Priority Registers are SFRs IP1 and IPH1.

The corresponding bits in each pair of Interrupt Priority Registers select one of the four
priority levels shown in 

Table 5-3

.

Note: NMI always has the highest priority (above Level 3), it does not use the level

selection shown in 

Table 5-3

.

Table 5-3

Interrupt Priority Level Selection 

IPH.x / IPH1.x

IP.x / IP1.x

Priority Level

0

0

Level 0 (lowest)

0

1

Level 1

1

0

Level 2

1

1

Level 3 (highest)

IP
Interrupt Priority Register

Reset Value: 00

H

7

6

5

4

3

2

1

0

0

PT2

PS

PT1

PX1

PT0

PX0

r

rw

rw

rw

rw

rw

rw

Field

Bits

Type Description

PX0

0

rw

Priority Level Low Bit for Interrupt Node XINTR0

PT0

1

rw

Priority Level Low Bit for Interrupt Node XINTR1

PX1

2

rw

Priority Level Low Bit for Interrupt Node XINTR2

PT1

3

rw

Priority Level Low Bit for Interrupt Node XINTR3

PS

4

rw

Priority Level Low Bit for Interrupt Node XINTR4

PT2

5

rw

Priority Level Low Bit for Interrupt Node XINTR5

0

7:6

r

Reserved

Returns 0 if read; should be written with 0.

*

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Eaton AMPGARD RVSS Instruction For Installation And Maintenance preview
AMPGARD RVSS
Бренд: Eaton Страницы: 16
Fagor CNC 8070 Programming Manual preview
CNC 8070
Бренд: Fagor Страницы: 556
Valcom V-1092 User Manual preview
V-1092
Бренд: Valcom Страницы: 3
Valcom V-1092 Technical Specifications preview
V-1092
Бренд: Valcom Страницы: 2
Zamel Extra Free RZB-02 Quick Manual preview
Extra Free RZB-02
Бренд: Zamel Страницы: 2
WAC T24-OD-CTR Installation Instruction preview
T24-OD-CTR
Бренд: WAC Страницы: 5
SDC E4KP ENTRYCHECK Operating Instructions Manual preview
E4KP ENTRYCHECK
Бренд: SDC Страницы: 6
Atmel AT91 ARM Thumb Application Note preview
AT91 ARM Thumb
Бренд: Atmel Страницы: 12
ICP DAS USA ALM-04-MRTU User Manual preview
ALM-04-MRTU
Бренд: ICP DAS USA Страницы: 26
National Instruments cRIO-FRC II User Manual And Specifications preview
cRIO-FRC II
Бренд: National Instruments Страницы: 22
Trikdis GV17 Short Installation Manual preview
GV17
Бренд: Trikdis Страницы: 7
M-Elec ML-2820-US3 Quick Start Manual preview
ML-2820-US3
Бренд: M-Elec Страницы: 2
ACT ACTPRO PRODUCT RANGE Operating & Installation Instructions Manual preview
ACTPRO PRODUCT RANGE
Бренд: ACT Страницы: 8
Doepke RJSG 1 Installation And Operating Manual preview
RJSG 1
Бренд: Doepke Страницы: 2
ICON ProCon C700 Series Operating Manual preview
ProCon C700 Series
Бренд: ICON Страницы: 30
aldes 611242-FC Installation Manual preview
611242-FC
Бренд: aldes Страницы: 3
Duke TSC-6/18M Installation Instructions preview
TSC-6/18M
Бренд: Duke Страницы: 4
Xylem Goulds ResiBoost RB111512 Instruction Manual preview
Goulds ResiBoost RB111512
Бренд: Xylem Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды