Infineon XC886CLM Скачать руководство пользователя страница 565 | Manualshive

Страница: 565 / 663

background image

XC886/888CLM

Analog-to-Digital Converter

User’s Manual

16-21

V1.3, 2010-02

ADC, V 1.0

After this addition, the complete result is stored in the selected result register. The result
event is generated and the valid bit becomes set.

It is possible to have an identical cycle behavior of the path to the result register, with the
data reduction filter being enabled or disabled. Furthermore, an overflow of the result
register is avoided, because a maximum of 2 conversion results are added (a 10-bit
result added twice delivers a maximum of 11 bits).

16.4.7.4

Result Register View

In order to cover a wide range of applications, the content of result register x (x = 0 - 3)
is available as different read views at different addresses (see

Figure 16-11

):

•

Normal read view RESRxL/H:
This view delivers the 8-bit or 10-bit conversion result.

•

Accumulated read view RESRAxL/H:
This view delivers the accumulated 9-bit or 11-bit conversion result.

All conversion results (with or without accumulation) are stored in the result registers, but
can be viewed at either RESRxL/H or RESRAxL/H which shows different data alignment
and width.

When the data reduction filter is enabled (DRCTR = 1), read access should be
performed on RESRAxL/H as it shows the full 9-bit (R8:R0) or 11-bit (R10:R0)
accumulated conversion result. Reading from RESRxL/H gives the appended (MSB
unavailable) accumulated result.

When the data reduction filter is disabled (DRCTR = 0), the user can read the 8-bit or
10-bit conversion result from either RESRxL/H or RESRAxL/H. In particular, for 8-bit
conversion (without accumulation), the result can be read from RESRxH with a single
instruction. Hence, depending on the application requirement, the user can choose to
read from the different views.

*

«
...
563
564
565
566
567
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: RadioMaster Страницы: 10

CEmarking RCX221

Бренд: Yamaha Страницы: 468

Бренд: mikroElektronika Страницы: 3

Бренд: Window Master Страницы: 7

Бренд: Samson Страницы: 44

Бренд: Beckhoff Страницы: 47

Бренд: DOTECH Страницы: 4

Бренд: MISUMI Страницы: 166

Бренд: Sunricher Страницы: 2

Бренд: DIG Страницы: 16

Бренд: NELSEN WATER Страницы: 16

Бренд: Newport Страницы: 72

Бренд: VRG Controls Страницы: 39

Бренд: Gardner Denver Страницы: 60

Бренд: Infineon Страницы: 28

POWER_AVR SVR TRI 3/3

Бренд: Ecus Страницы: 58

exta life ROB-21

Бренд: Zamel Страницы: 24

SECURBASE LIGHT PLUS

Бренд: BFT Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды