Infineon XC886CLM Скачать руководство пользователя страница 434 | Manualshive

Страница: 434 / 663

background image

XC886/888CLM

Capture/Compare Unit 6

User’s Manual

14-82

V1.3, 2010-02

CCU6, V 1.0

Note: Not all bits in register IS can generate an interrupt. Other status bits have been

added, which have a similar structure for their set and reset actions.

Note: The interrupt generation is independent from the value of the bits in register IS,

e.g. the interrupt will be generated (if enabled) even if the corresponding bit is
already set. The trigger for an interrupt generation is the detection of a set
condition (by hardware or software) for the corresponding bit in register IS.

Note: In compare mode (and hall mode), the timer-related interrupts are only generated

while the timer is running (TxR = 1). In capture mode, the capture interrupts are
also generated while the timer T12 is stopped.

Register ISS contains the individual interrupt request set bits required to generate a
CCU6 interrupt request by software.

WHE

5

rh

Wrong Hall Event

On every valid hall edge, the contents of EXPH are
compared with the pattern on pin CCPOSx. If both
comparisons (CURH and EXPH with CCPOSx) are not
true, bit WHE (wrong hall event) is set.
0

A transition to a wrong hall event (not the
expected one) has not yet been detected since
this bit has been reset for the last time.

1

A transition to a wrong hall event (not the
expected one) has been detected.

IDLE

6

rh

IDLE State

This bit is set together with bit WHE (wrong hall event)
and it must be reset by software.
0

No action.

1

Bit field MCMP is cleared and held to 0, the
selected outputs are set to passive state.

STR

7

rh

Multi-Channel Mode Shadow Transfer Request

This bit is set when a shadow transfer from
MCMOUTS to MCMOUT takes places in multi-channel
mode.
0

The shadow transfer has not yet taken place.

1

The shadow transfer has taken place.

Field

Bits

Type Description

*

«
...
432
433
434
435
436
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: We Care Solar Страницы: 46

Бренд: ITALFARAD Страницы: 32

Бренд: Rabbit Страницы: 12

Бренд: bluelab Страницы: 39

Бренд: Kohzu Precision Страницы: 58

Бренд: 4IPNET Страницы: 11

10 AMP RVC-MPPT

Бренд: Go Power Страницы: 17

Бренд: DH Instruments Страницы: 30

Sigma II Series

Бренд: YASKAWA Страницы: 359

Бренд: Pixsys Страницы: 24

Бренд: Rain Bird Страницы: 7

Бренд: CAME Страницы: 32

Бренд: JLCooper Electronics Страницы: 11

Бренд: Anaheim Automation Страницы: 35

ALGAS-QA Series

Бренд: BIFFI Страницы: 46

Бренд: Evak Страницы: 10

ProCon D700 Series

Бренд: ICON Страницы: 29

Бренд: alpro Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды