manualshive.com logo in svg

Infineon XC886CLM, Руководство пользователя

Infineon XC886CLM - микроконтроллер с высокой производительностью для широкого спектра применений. Пользователи могут скачать руководство пользователя бесплатно на manualshive.com, чтобы узнать больше о функциях и настройках этого продукта. Управляйте своими проектами с легкостью, благодаря нашему подробному руководству.

Поделиться
Скачать
background image

XC886/888CLM

Controller Area Network (MultiCAN) Controller

 

User’s Manual

15-38

V1.3, 2010-02

MultiCAN, V1.0

 

15.1.9.7

Gateway Mode

The gateway mode allows an automatic information transfer to be established between
two independent CAN buses without CPU interaction.

The gateway mode operates on message object level. In gateway mode, information is
transferred between two message objects, resulting in an information transfer between
the two CAN nodes to which the message objects are allocated. A gateway may be
established with any pair of CAN nodes, and there can be as many gateways as there
are message objects available to build the gateway structure.

Gateway mode is selected by setting MOFCRs.MMC = 0100

B

 of the gateway source

object s. The gateway destination object d is selected by the MOFGPRd.CUR pointer of
the source object. The gateway destination object only needs to be valid (its
MSGVAL = 1). All other settings are not relevant for the information transfer from the
source object to the destination object.

A gateway source object s behaves like a standard message object except some
additional actions are performed by the MultiCAN module when a CAN frame has been
received and stored in the source object (see 

Figure 15-14

):

1. If bit MOFCRs.DLCC is set, the data length code MOFCRs.DLC is copied from the

gateway source object to the gateway destination object.

2. If bit MOFCRs.IDC is set, the identifier MOARs.ID and the identifier extension

MOARs.IDE are copied from the gateway source object to the gateway destination
object.

3. If bit MOFCRs.DATC is set, the data bytes stored in the two data registers

MODATALs and MODATAHs are copied from the gateway source object to the
gateway destination object. All 8 data bytes are copied, even if MOFCRs.DLC
indicates less than 8 data bytes.

4. If bit MOFCRs.GDFS is set, the transmit request flag MOSTATd.TXRQ is set in the

gateway destination object.

5. The receive pending bit MOSTATd.RXPND and the new data bit

MOSTATd.NEWDAT are set in the gateway destination object.

6. A message interrupt request is generated for the gateway destination object if its

MOSTATd.RXIE is set.

7. The current object pointer MOFGPRs.CUR of the gateway source object is moved to

the next destination object according to the FIFO rules as described on 

Page 15-34

.

A gateway with a single (static) destination object is obtained by setting
MOFGPRs.TOP = MOFGPRs.BOT = MOFGPRs.CUR = destination object.

The link from the gateway source object to the gateway destination object works in the
same way as the link from a FIFO base to a FIFO slave. This means that a gateway with
an integrated destination FIFO may be created; in 

Figure 15-13

, where the object on the

left is the gateway source object and the message object on the right side is the gateway
destination objects.

*

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

ABATEC A1 Installation And Operation Instruction Manual preview
A1
Бренд: ABATEC Страницы: 8
Baader Planetarium Steeldrive II Manual preview
Steeldrive II
Бренд: Baader Planetarium Страницы: 7
Danfoss VLT MCD 200 Installation Manual preview
VLT MCD 200
Бренд: Danfoss Страницы: 32
Danfoss VLT AutomationDrive FC 360 Programming Manual preview
VLT AutomationDrive FC 360
Бренд: Danfoss Страницы: 60
Danfoss AMV 110 NL AQT Datasheet preview
AMV 110 NL AQT
Бренд: Danfoss Страницы: 4
Danfoss ECL Comfort 110 Quick Manual preview
ECL Comfort 110
Бренд: Danfoss Страницы: 2
Data Aire dap4 touch Protocol Manual preview
dap4 touch
Бренд: Data Aire Страницы: 13
Taco Electronic Solutions iWorx MPU2 Installation Manual preview
iWorx MPU2
Бренд: Taco Electronic Solutions Страницы: 28
Eaton FC18 User Manual preview
FC18
Бренд: Eaton Страницы: 10
+GF+ EA15 Instruction Manual preview
EA15
Бренд: +GF+ Страницы: 3
ZiLOG Z8 Encore! XP Dual F1680 Series User Manual preview
Z8 Encore! XP Dual F1680 Series
Бренд: ZiLOG Страницы: 18
Danfoss AME 56K Instructions Manual preview
AME 56K
Бренд: Danfoss Страницы: 10
Zero 88 Chilli Master Operating Manual preview
Chilli Master
Бренд: Zero 88 Страницы: 34
NEC mPD789101 User Manual preview
mPD789101
Бренд: NEC Страницы: 265
National Instruments PXI-8232 Installation Manual preview
PXI-8232
Бренд: National Instruments Страницы: 8
TIE AMBITECH BRAKE-PAK Installation & Setup Instructions preview
AMBITECH BRAKE-PAK
Бренд: TIE Страницы: 5
SUPMEA SUP-PH8.0 User Manual preview
SUP-PH8.0
Бренд: SUPMEA Страницы: 32
KORINS EPIP-40 /30A(I) Instruction Manual preview
EPIP-40 /30A(I)
Бренд: KORINS Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды