Infineon XC886CLM Скачать руководство пользователя страница 462 | Manualshive

Страница: 462 / 663

background image

XC886/888CLM

Controller Area Network (MultiCAN) Controller

User’s Manual

15-18

V1.3, 2010-02

MultiCAN, V1.0

15.1.5

CAN Node Analysis Features

This section describes the CAN node analysis capabilities of the MultiCAN module.

15.1.5.1

Analyze Mode

The CAN analyze mode allows the CAN traffic to be monitored without affecting the
logical state of the CAN bus. The CAN analyze mode is selected by setting bit
NCRx.CALM.

In CAN analyze mode, the transmit pin of a CAN node is held on recessive level
permanently. The CAN node may receive frames (data, remote, and error frames) but is
not allowed to transmit. Received data/remote frames are not acknowledged (i.e.,
acknowledge slot is sent recessive) but will be received and stored in matching message
objects as long as there is any other node that acknowledges the frame. The complete
message object functionality is available but no transmit request will be executed.

15.1.5.2

Loop-Back Mode

The MultiCAN module provides a loop-back mode to enable an in-system test of the
MultiCAN module as well as the development of CAN driver software without access to
an external CAN bus.

The loop-back feature consists of an internal CAN bus (inside the MultiCAN module) and
a bus select switch for each CAN node. With the switch, each CAN node can be
connected either to the internal CAN bus (loop-back mode activated) or the external
CAN bus, respectively to its transmit or receive pin (normal operation). The CAN bus
which is currently not selected is driven recessive, this means the transmit pin is held at
1 and the receive pin is ignored by the CAN nodes that are in loop-back mode.

The loop-back mode is selected by setting bit NPCRx.LBM. All CAN nodes that are in
loop-back mode may communicate together via the internal CAN bus without affecting
the normal operation of the other CAN nodes that are not in loop-back mode.

*

«
...
460
461
462
463
464
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: Daikin Страницы: 5

Бренд: Salda Страницы: 16

Бренд: Jetter Страницы: 24

Бренд: Anilam Страницы: 31

Бренд: Joy-it Страницы: 7

Бренд: adept technology Страницы: 96

Бренд: Danfoss Страницы: 22

MODACT MTNED 15

Бренд: ZPA Pecky, a.s. Страницы: 48

Бренд: Cablematic Страницы: 6

Бренд: Parker Страницы: 31

Бренд: Infineon Страницы: 14

Бренд: Keysight Страницы: 22

komplete kontrol s series

Бренд: Native Instruments Страницы: 338

Бренд: Electrosmith Страницы: 32

Бренд: MRC Страницы: 2

Бренд: Garmin Страницы: 4

3174/3274 I-Mux Series

Бренд: Black Box Страницы: 20

Бренд: Abus Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды