Infineon XC886CLM Скачать руководство пользователя страница 492 | Manualshive

Страница: 492 / 663

background image

XC886/888CLM

Controller Area Network (MultiCAN) Controller

User’s Manual

15-48

V1.3, 2010-02

MultiCAN, V1.0

15.2.1

Global Module Registers

All list operations such as allocation, de-allocation and relocation of message objects
within the list structure are performed via the Command Panel. It is not possible to modify
the list structure directly by software by writing to the message objects and the LIST
registers.

The Panel Control Register PANCTR is used to start a new command by writing the
command arguments and the command code into its bit fields.

PANCTR
Panel Control Register

Reset Value: 0000 0301

H

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

PANAR2

PANAR1

rwh

rwh

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

0

RBU

SY

BUS

Y

PANCMD

r

rh

rh

rwh

Field

Bits

Type Description

PANCMD

[7:0]

rwh

Panel Command

This bit field is used to start a new command by
writing a panel command code into it. At the end of a
panel command, the NOP (no operation) command
code is automatically written into PANCMD. The
coding of PANCMD is defined in

BUSY

8

rh

Panel Busy Flag

0

Panel has finished command and is ready to
accept a new command.

1

Panel operation is in progress.

RBUSY

9

rh

Result Busy Flag

0

No update of PANAR1 and PANAR2 is
scheduled by the list controller.

1

A list command is running (BUSY = 1) that will
write results to PANAR1 and PANAR2, but the
results are not yet available.

*

«
...
490
491
492
493
494
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: e-BLEACH Страницы: 24

iBox Hub 25020180

Бренд: Hans Grohe Страницы: 36

Бренд: Samson Страницы: 6

Бренд: Dantherm Страницы: 20

Бренд: J+J Страницы: 4

Бренд: Velleman Страницы: 12

FX-COMM4NDER MFX3203

Бренд: Magicfx Страницы: 16

Бренд: DAYLIFF Страницы: 40

Бренд: Altronic Страницы: 70

Бренд: Matrix Страницы: 10

Бренд: ZALMAN Страницы: 8

Бренд: 9g Products Страницы: 12

Бренд: Automation Direct Страницы: 9

Бренд: UNIT ELECTRONICS Страницы: 40

IC 912 LX Pt100 R

Бренд: Eliwell Страницы: 8

Бренд: NEC Страницы: 1053

Бренд: Acclaim Lighting Страницы: 41

Бренд: Hyster Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды