Infineon XC886CLM Скачать руководство пользователя страница 449 | Manualshive

Страница: 449 / 663

background image

XC886/888CLM

Controller Area Network (MultiCAN) Controller

User’s Manual

15-5

V1.3, 2010-02

MultiCAN, V1.0

•

Error Handling Unit

The Error Handling Unit manages the receive and transmit error counter. According
to the contents of both counters, the CAN node is set into an error-active, error
passive or bus-off state.

•

Node Control Unit

The Node Control Unit coordinates the operation of the CAN node:
– Enable/disable CAN transfer of the node
– Enable/disable and generate node-specific events that lead to an interrupt request

(CAN bus errors, successful frame transfers etc.)

– Administration of the Frame Counter

•

Interrupt Control Unit

The Interrupt Control Unit in the CAN node controls the interrupt generation for the
different conditions that can occur in the CAN node.

Message Controller

The Message Controller handles the exchange of CAN frames between the CAN nodes
and the message objects that are stored in the Message RAM. The Message Controller
performs several functions:

•

Receive acceptance filtering to determine the correct message object for storing of a
received CAN frame

•

Transmit acceptance filtering to determine the message object to be transmitted first,
individually for each CAN node

•

Transfer contents between message objects and the CAN nodes, taking into account
the status/control bits of the message objects

•

Handling of the FIFO buffering and gateway functionality

•

Aggregation of message-pending notification bits

List Controller

The List Controller performs all operations that lead to a modification of the double-
chained message object lists. Only the list controller is allowed to modify the list
structure. The allocation/deallocation or reallocation of a message object can be
requested via a user command interface (command panel). The list controller state
machine then performs the requested command autonomously.

Interrupt Control

The general interrupt structure is shown in

Figure 15-3

. The interrupt event can trigger

the interrupt generation. The interrupt pulse is generated independently from the
interrupt flag in the interrupt status register. The interrupt flag can be reset by software
by writing a 0 to it.

If enabled by the related interrupt enable bit in the interrupt enable register, an interrupt
pulse can be generated at one of the 8 interrupt output lines CANSRCm of the MultiCAN

*

«
...
447
448
449
450
451
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

ControlMaster CM15

Бренд: ABB Страницы: 4

Бренд: Vacon Страницы: 64

Бренд: ADEMCO Страницы: 2

Бренд: Delta Страницы: 16

Бренд: Sunlover Страницы: 2

multicomp F144-MS-1V1C1TI6RO-3

Бренд: KBR Страницы: 68

MOBA-Matic MMC-1000

Бренд: MOBA Страницы: 172

Бренд: Danfoss Страницы: 36

Бренд: maxon motor Страницы: 44

Бренд: Jung Страницы: 8

Бренд: Fisher Страницы: 44

Бренд: Galcon Страницы: 24

freescale Kinetics TWR-K60N512-KEIL

Бренд: NXP Semiconductors Страницы: 5

ServeRAID M1215 SAS

Бренд: IBM Страницы: 35

Бренд: SAES Страницы: 36

Бренд: Zamel Страницы: 2

Бренд: EP Solar Страницы: 3

Бренд: VelLight Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды