manualshive.com logo in svg

Infineon XC886CLM, Руководство пользователя, Страница: 217 / 663

Поделиться
Скачать
Infineon XC886CLM Скачать руководство пользователя страница 217

XC886/888CLM

Power Supply, Reset and Clock Management

 

User’s Manual

7-18

V1.3, 2010-02

Power, Reset and Clock, V 1.0

 

PLL_CON
PLL Control Register

 

Reset Value: 1001 0000

B

7

6

5

4

3

2

1

0

NDIV

VCOBYP

OSCDISC

RESLD

LOCK

rw

rw

rw

rwh

rh

Field

Bits

Type Description

LOCK

0

rh

PLL Lock Status Flag

0

PLL is not locked.

1

PLL is locked.

RESLD

1

rwh

Restart Lock Detection

Setting this bit will reset the PLL lock status flag and 
restart the lock detection. This bit will automatically 
be reset to 0 and thus always be read back as 0.
0

No effect

1

Reset lock flag and restart lock detection

OSCDISC

2

rw

Oscillator Disconnect

0

Oscillator is connected to the PLL.

1

Oscillator is disconnected from the PLL.

VCOBYP

3

rw

PLL VCO Bypass Mode Select

0

Normal operation (default)

1

VCO bypass mode (PLL output clock is 
derived from input clock divided by P- and 
K-dividers).

*

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов