Infineon XC886CLM Скачать руководство пользователя страница 475 | Manualshive

Страница: 475 / 663

background image

XC886/888CLM

Controller Area Network (MultiCAN) Controller

User’s Manual

15-31

V1.3, 2010-02

MultiCAN, V1.0

RTSEL

When a message object has been identified after transmission acceptance filtering to be
transmitted next, bit MOCTRn.RTSEL (“Receive/Transmit Selected”) becomes set.

When the message object is copied into the internal transmit buffer, bit RTSEL is
checked, and the message is only transmitted if RTSEL = 1. After the successful
transmission of the message, bit RTSEL is checked again and the message
postprocessing is only executed if RTSEL = 1.

For a complete re-configuration of a valid message object, the following steps should be
executed:

1. Clear MSGVAL bit
2. Re-configure the message object while MSGVAL = 0
3. Clear RTSEL and set MSGVAL

Clearing of RTSEL ensures that the message object is disconnected from an
ongoing/scheduled transmission and no message object processing (copying message
to transmit buffer including clearing NEWDAT, clearing TXRQ, time stamp update,
message interrupt, etc.) within the old context of the object can occur after the message
object becomes valid again, but within a new context.

NEWDAT

When the content of a message object has been transferred to the internal transmit
buffer of the CAN node, bit MOSTATn.NEWDAT (New Data) is cleared by hardware to
indicate that the transmit message object data is no longer new.

When the transmission of the frame is successful and NEWDAT is still cleared (if no new
data has been copied into the message object meanwhile), TXRQ (Transmit Request) is
cleared automatically by hardware.

If, however, the NEWDAT bit has been set again by the software (because a new frame
is to be transmitted), TXRQ is not cleared to enable the transmission of the new data.

TXEN1

Transmit Enable 1

This bit is used in transmit FIFOs to select the message object that is
transmit active within the FIFO structure.
For message objects that are not transmit FIFO elements, TXEN1 can
either be set permanently to 1 or can be used as a second independent
transmission enable bit.

Table 15-3

Message Transmission Bit Definitions

(cont’d)

Bit

Description

*

«
...
473
474
475
476
477
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: T-Verter Страницы: 121

Бренд: Happy Страницы: 10

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Бренд: Newport Страницы: 417

Бренд: Computer Automation Technology Страницы: 55

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 340

Бренд: ETC Страницы: 8

Бренд: Texas Instruments Страницы: 27

Бренд: Vageo Страницы: 2

Бренд: WINDY NATION Страницы: 16

Бренд: Nice Страницы: 32

Synergy SGY-101

Бренд: Fairford Страницы: 20

Бренд: ST Страницы: 40

Бренд: Varian Страницы: 37

Бренд: GCE Страницы: 46

Бренд: Tusa Страницы: 72

Бренд: Danfoss Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды