Infineon XC886CLM Скачать руководство пользователя страница 480 | Manualshive

Страница: 480 / 663

background image

XC886/888CLM

Controller Area Network (MultiCAN) Controller

User’s Manual

15-36

V1.3, 2010-02

MultiCAN, V1.0

15.1.9.5

Receive FIFO

The Receive FIFO structure is used to buffer incoming (received) remote or data frames.

A Receive FIFO is selected by setting MOFCRn.MMC = 0001

B

in the FIFO base object.

This MMC code automatically designates a message object as FIFO base object. The
message modes of the FIFO slave objects are not relevant for the operation of the
Receive FIFO.

When the FIFO base object receives a frame from the CAN node it belongs to, the frame
is not stored in the base object itself but in the message object that is selected by the
base object’s MOFGPRn.CUR pointer. This message object receives the CAN message
as if it is the direct receiver of the message. However, MOFCRn.MMC = 0000

B

is

implicitly assumed for the FIFO slave object, and a standard message delivery is
performed. The actual message mode (MMC setting) of the FIFO slave object is ignored.
For the slave object, no acceptance filtering takes place that checks the received frame
for a match with the identifier, IDE bit, and DIR bit.

With the reception of a CAN frame, the current pointer CUR of the base object is set to
the number of the next message object in the FIFO structure. This message object will
then be used to store the next incoming message.

If bit field MOFCRn.OVIE (“Overflow Interrupt Enable”) of the FIFO base object is set and
the current pointer MOFGPRn.CUR becomes equal to MOFGPRn.SEL, a FIFO overflow
interrupt request is generated. This interrupt request is generated on interrupt node
TXINP of the base object immediately after the storage of the received frame in the slave
object. Transmit interrupts are still generated if TXIE is set.

A CAN message is stored in FIFO base and slave object only if MSGVAL = 1.

*

«
...
478
479
480
481
482
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

CompactRIO cRIO-9002

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 145

Бренд: National Instruments Страницы: 42

Бренд: National Instruments Страницы: 8

Бренд: Zander Aachen Страницы: 44

Extra Free ROB-01/12-24V

Бренд: Zamel Страницы: 2

Бренд: EasyIO Страницы: 17

Бренд: Shimaden Страницы: 32

Бренд: phytron Страницы: 55

Бренд: EBS Страницы: 116

Бренд: Daikin Страницы: 2

GreenMax DRC DRC07-ED0

Бренд: Leviton Страницы: 2

Бренд: Danfoss Страницы: 14

Бренд: V2 Страницы: 108

Бренд: C Systems Страницы: 4

Бренд: Zennio Страницы: 30

Бренд: Freescale Semiconductor Страницы: 41

Бренд: mikroElektronika Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды