Infineon XC886CLM Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 663

background image

XC886/888CLM

Introduction

User’s Manual

1-1

V1.3, 2010-02

Introduction, V 1.1

1

Introduction

The XC886/888 is a member of the high-performance XC800 family of 8-bit
microcontrollers. It is based on the XC800 Core that is compatible with the industry
standard 8051 processor. Furthermore, the XC886/888 is a superset of the Infineon
XC866 8-bit microcontroller, thus offering an easy upgrade path for XC866 users.

The XC886/888 features both a CAN controller and LIN support integrated on a single
chip to provide advance networking capabilities. The on-chip CAN module reduces the
CPU load by performing most of the functions required by the networking protocol
(masking, filtering and buffering of CAN frames).

The XC886/888 is equipped with either embedded Flash memory to offer high flexibility
in development and ramp-up, or compatible ROM versions to provide cost-saving
potential in high-volume production. The XC886/888 memory protection strategy
features read-out protection of user intellectual property (IP), along with Flash program
and erase protection to prevent data corruption.

The multi-bank Flash architecture supports In-Application Programming (IAP), allowing
user program to modify Flash contents during program execution. In-System
Programming (ISP) is available through the Boot ROM-based BootStrap Loader (BSL),
enabling convenient programming and erasing of the embedded Flash via an external
host (e.g., personal computer).

Other key features include a Capture/Compare Unit 6 (CCU6) for the generation of pulse
width modulated signal with special modes for motor control; a 10-bit Analog-to-Digital
Converter (ADC) with extended functionalities such as autoscan and result accumulation
for anti-aliasing filtering or for averaging; a Multiplication/Division Unit (MDU) to support
the XC800 Core in math-intensive real-time control applications; a CORDIC (COrdinate
Rotation DIgital Computer) Coprocessor for high-speed computation of trigonometric,
linear or hyperbolic functions; and an On-Chip Debug Support (OCDS) unit for software
development and debugging of XC800-based systems.

The XC886/888 also features an on-chip oscillator and an integrated voltage regulator
to allow a single voltage supply of 3.3 or 5.0 V. For low power applications, various power
saving modes are available for selection by the user. Control of the numerous on-chip
peripheral functionalities is achieved by extending the Special Function Register (SFR)
address range with an intelligent paging mechanism optimized for interrupt handling.

*

«
...
13
14
15
16
17
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

ControlMaster CM15

Бренд: ABB Страницы: 28

Бренд: ABATEC Страницы: 8

Бренд: SYCLOPE electronic Страницы: 40

Bell & Gossett Technologic PPS

Бренд: Xylem Страницы: 20

Бренд: Swagelok Страницы: 20

Бренд: FuzzDog Страницы: 9

DMC-40x0 Series

Бренд: Galil Motion Control Страницы: 280

Z8 Encore! XP Dual F1680 Series

Бренд: ZiLOG Страницы: 18

Бренд: Danfoss Страницы: 10

PCI-to-IDE ATA-133

Бренд: Acard Страницы: 33

Бренд: Maverick Страницы: 122

EPIP-40 /30A(I)

Бренд: KORINS Страницы: 3

Бренд: meibes Страницы: 20

Бренд: Telit Wireless Solutions Страницы: 49

Бренд: Dieffematic Страницы: 9

Бренд: Bamo Страницы: 10

RAPTOR BLS-Mini

Бренд: Flycolor Страницы: 2

Бренд: Toky Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды