Infineon XC886CLM Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 663

background image

XC886/888CLM

Memory Organization

User’s Manual

3-8

V1.3, 2010-02

Memory Organization, V 1.2

Note: For ROM devices, bits 5 to 7 are not applicable and should be written with zeros.

Setting bit 4 enables the protection of D-Flash from accidental erase, i.e.
DFLASHEN bit must be set prior to each erase operation.

BSL mode 6, which is used for enabling Flash protection, can also be used for disabling
Flash protection. Here, the programmed password must be provided by the user. A
password match triggers an automatic erase of the protected P-Flash and D-Flash
contents, including the programmed password. The Flash protection is then disabled
upon the next reset.

For the ROM device, the ROM is protected at all times and BSL mode 6 is used only to
block external access to the device. However, unlike the Flash device, it is not possible
to disable the memory protection of the ROM device. Here, entering BSL mode 6 will
result in a protection error.

Note: If ROM read-out protection is enabled, only read instructions in the ROM memory

can target the ROM contents.

Table 3-2

User Programmable Password Bit Fields

Bits

Size

Usage

Value

7

1-bit

Flash hardware
protection mode
selection bit

0

Flash hardware protection mode 0 is
selected.

1

Flash hardware protection mode 1 is
selected.

6:5

2-bit

Select field for Flash
banks to be erased
during unprotection

00

Only P-Flash banks are erased during
unprotection.

01

P-Flash banks and D-Flash bank 0 are
erased during unprotection.

10

P-Flash banks and D-Flash bank 1 are
erased during unprotection.

11

All Flash banks (P-Flash and D-Flash)
are erased during unprotection.

Note: If bit 7 of password is set, all Flash

banks will be erased during
unprotection, regardless of the value
of bits 4 to 6.

4

1-bit

Flash hardware
protection enable bit

0

Flash hardware protection will not be
activated.

1

Flash hardware protection will be
activated.

3:0

4-bit

User-defined password
field

This password field must be a non-zero
value.

*

«
...
53
54
55
56
57
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: Danfoss Страницы: 36

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

Бренд: Koer Страницы: 6

Бренд: CORNING Страницы: 142

Бренд: Elotech Страницы: 20

Бренд: Intermatic Страницы: 2

E4KP ENTRYCHECK

Бренд: SDC Страницы: 6

Бренд: OMEGA AIR Страницы: 12

Бренд: DIG Страницы: 16

ERO-32AP-0 V1.4

Бренд: Darco Страницы: 14

Бренд: Rainmachine Страницы: 22

M2M Smart Service Developer Kit

Бренд: Kontron Страницы: 27

Бренд: WAGO Страницы: 2

Бренд: S2Tech Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды