Infineon XC886CLM Скачать руководство пользователя страница 472 | Manualshive

Страница: 472 / 663

background image

XC886/888CLM

Controller Area Network (MultiCAN) Controller

User’s Manual

15-28

V1.3, 2010-02

MultiCAN, V1.0

context of the message object. Therefore, a message object re-configuration should
consist of the following steps:

1. Clear MSGVAL bit
2. Re-configure the message object while MSGVAL = 0
3. Clear RTSEL bit and set MSGVAL again

RXEN

Bit MOSTATn.RXEN enables a message object for frame reception. A message object
can receive CAN messages from the CAN bus only if RXEN = 1. The MultiCAN module
evaluates RXEN only during receive acceptance filtering. After receive acceptance
filtering, RXEN is ignored and has no further influence on the actual storage of a received
message in a message object.

Bit RXEN enables the “soft phase out” of a message object: after clearing RXEN, a
currently received CAN message for which the message object has won acceptance
filtering is still stored in the message object but for subsequent messages the message
object no longer wins receive acceptance filtering.

RXUPD, NEWDAT and MSGLST

An ongoing frame storage process is indicated by the bit MOSTATn.RXUPD (“Receive
Updating”). RXUPD is set with the start and cleared with the end of a message object
update (which consists of frame storage as well as flag updates).

After storing the received frame (identifier, IDE bit, DLC and the data field for data frames
as well) the bit MOSTATn.NEWDAT (“New Data”) is set. If NEWDAT was already set
before it becomes set again, bit MOSTATn.MSGLST (“Message Lost”) is set to indicate
a data loss condition.

The RXUPD and NEWDAT flags can help to read consistent frame data from the
message object during an ongoing CAN operation. The following steps are
recommended to be executed:

1. Clear NEWDAT bit.
2. Read message content (identifier, data etc.) from the message object.
3. Check that both NEWDAT and RXUPD are cleared. If this is not the case, go back to

step 1.

4. As step 3 was successful, the message object content is consistent, i.e., has not

been updated by the MultiCAN module while reading.

Bits RXUPD, NEWDAT and MSGLST have the same behavior for the reception of data
as well as remote frames.

*

«
...
470
471
472
473
474
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: Ubisys Страницы: 2

Бренд: XVision Страницы: 28

Бренд: YASKAWA Страницы: 61

Бренд: YASKAWA Страницы: 49

Бренд: M-system Страницы: 17

Бренд: RAM Страницы: 71

Бренд: Voltech Страницы: 8

Бренд: Audioaccess Страницы: 2

ESP32-C3 Series

Бренд: Espressif Systems Страницы: 30

Бренд: Neets Control Страницы: 12

total control MRX-10

Бренд: Universal Remote Control Страницы: 16

Бренд: MSA Страницы: 309

Бренд: SAES Страницы: 36

Бренд: Cablematic Страницы: 6

Бренд: Fright Ideas Страницы: 2

Бренд: Omega Страницы: 56

Governor TEN014980

Бренд: Gardner Denver Страницы: 194

Бренд: Grundfos Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды