Infineon XC886CLM Скачать руководство пользователя страница 608

Страница: 608 / 663

XC886/888CLM

On-Chip Debug Support

User’s Manual

17-1

V1.3, 2010-02

OCDS, V 1.0

On-Chip Debug Support

The On-Chip Debug Support (OCDS) provides the basic functionality required for
software development and debugging of XC800-based systems.

The OCDS design is based on these principles:

•

Use the built-in debug functionality of the XC800 Core

•

Add a minimum of hardware overhead

•

Provide support for most of the operations by a Monitor Program

•

Use standard interface to communicate with the Host (a Debugger)

17.1

Features

The main debug features supported are:

•

Set breakpoints on instruction address and on address range within the Program
Memory

•

Set breakpoints on Internal RAM address range

•

Support unlimited software breakpoints in Flash/RAM code region

•

Process external breaks via JTAG and upon activating a dedicated pin

•

Step through the program code

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание XC886CLM

Отзывы:

Похожие инструкции для XC886CLM

Бренды по названию

Популярные бренды

Infineon XC886CLM, Руководство пользователя

Результаты поиска

Содержание XC886CLM

Отзывы:

Похожие инструкции для XC886CLM

Бренды по названию

Популярные бренды