Infineon XC886CLM Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 663

background image

XC886/888CLM

Memory Organization

User’s Manual

3-19

V1.3, 2010-02

Memory Organization, V 1.2

3.5.4.1

Bit Protection Scheme

The bit protection scheme prevents direct software writing of selected bits (i.e., protected
bits) using the PASSWD register. When the bit field MODE is 11

B

, writing 10011

B

to the

bit field PASS opens access to writing of all protected bits, and writing 10101

B

to the bit

field PASS closes access to writing of all protected bits. In both cases, the value of the
bit field MODE is not changed even if PASSWD register is written with 98

H

or A8

H

. It can

only be changed when bit field PASS is written with 11000

B

, for example, writing D0

H

to

PASSWD register disables the bit protection scheme.

Note that access is opened for maximum 32 CCLKs if the “close access” password is not
written. If “open access” password is written again before the end of 32 CCLK cycles,
there will be a recount of 32 CCLK cycles. The protected bits include the N- and K-
Divider bits, NDIV and KDIV; the Watchdog Timer enable bit, WDTEN; and the power-
down and slow-down enable bits, PD and SD.

PASSWD
Password Register

Reset Value: 07

H

7

6

5

4

3

2

1

0

PASS

PROTECT

_S

MODE

wh

rh

rw

Field

Bits

Type Description

MODE

[1:0]

rw

Bit Protection Scheme Control bits

00

Scheme disabled - direct access to the
protected bits is allowed.

11

Scheme enabled - the bit field PASS has to be
written with the passwords to open and close
the access to protected bits. (default)

Others: Scheme enabled
These two bits cannot be written directly. To change
the value between 11

B

and 00

B

, the bit field PASS

must be written with 11000

B

; only then, will the

MODE[1:0] be registered.

PROTECT_S

2

rh

Bit Protection Signal Status bit

This bit shows the status of the protection.
0

Software is able to write to all protected bits.

1

Software is unable to write to any protected
bits.

*

«
...
64
65
66
67
68
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

7000-2 - Escalade RAID Controller

Бренд: 3Ware Страницы: 2

Бренд: Abicor Binzel Страницы: 8

Бренд: Rain Bird Страницы: 138

Бренд: Ultratec Страницы: 33

Бренд: Eaton Страницы: 448

Бренд: Daruifuno Страницы: 24

PetroVend PV200

Бренд: OPW Страницы: 2

Бренд: Frico Страницы: 12

Бренд: Woodward Страницы: 32

Бренд: McIntosh Страницы: 60

Бренд: Ruida Technology Страницы: 45

Бренд: Stramatel Страницы: 10

Бренд: Kelly Страницы: 32

Dynamic Boiler Controller

Бренд: Intiel Страницы: 25

Бренд: CDVI Страницы: 24

exta life SRM-22

Бренд: Zamel Страницы: 5

Бренд: Walchem Страницы: 35

Бренд: AL-KO Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды