background image

RF

ontroller

is intended for access control in auxiliary, industrial and inhabited buildings and

premises and is able to control either electromagnetic or electromechanical lock.

ontroller con

reader

and control unit                   and may be used as

part of doorphone as well as stand-alone system.

.

Entrance door unlocking

ACCESS keys

Entrance door unlocking by pressing the indoor EXIT button
Guard mode can be enabled

disabled with a GUARD

or

MASTER key              All ACCESS keys are disabled in this mode

Programmable unlocked state duration
Light

sound indication of operating modes

MASTER key memorizing
GUARD

ACCESS keys memorizing and erasing

All data erasing

RF- keys, lock and EXIT

button are available upon request.

ontrol nit contains dangerous for life high voltage -

.

Unplu

the unit before replacing

fuse and connecting wires.To avoid damage or electric shock do not make any

repair when the power is on.

No metallic objects shall penetrate into ventilation openings of the unit. The unit shall not be exposed to dripping or

splashing and no objects filled with liquids shall be placed on the unit.

C

,

RF c

tains the

the

a

with

(up to 2680 keys)

or

key (up to 28 keys)

the

-

(1 key).

Built-in power supply for lock and doorstation

1 s or 7 s

and

-

and

300M

The c

u

g

the

The mains plug shall remain readily operable.

VIZIT-KTM60 R

KTM60

Only VIZIT-RF2 keys (125 KHz ) are supported

FEATURES

PARTS LIST

SAFETY INSTRUCTIONS

230

2

RD-3

2M,

WARNING!

V

·

·

·

·

·

·

·

·

·

Operating Instruction

x 1

x 1

x 1

Control unit

KTM602M

Reader

RD-3

Fasteners

Screw 3.5 25

-

х

Anchor - 6х30

for control unit

KTM602M

x 4

x 4

for reader

RD-3

Screw 3.5 3

-

х 0

x 2

x 2

Gag

x 4

Anchor - 6х30

www.vizit.eu

VIZIT-КТМ602R

1/6

OPERATING INSTRUCTION

VIZIT-КТМ602R

OPERATING INSTRUCTION

Содержание KTM602R







Отзывы: