manualshive.com logo in svg

Huawei SmartAX MA5616, Руководство по настройке

"Huawei SmartAX MA5616" - высококачественное оборудование для настройки и управления сетями. Здесь вы можете бесплатно скачать "Configuration Manual" и другие руководства по использованию. Посетите manualshive.com, чтобы скачать нужные руководства.

Поделиться
Скачать
background image

mask 255.255.255.0 gateway 192.168.50.254 vlan 8

huawei(config-if-gpon-0/2)#

quit

c.

Configure an inband management service port.
Configure the management service port index to 0, management VLAN ID to 8,
GEM port ID to 0, and CVLAN ID to 8. On the OLT, the rate of the inband
service port is not limited. Therefore, use default traffic profile 6. To limit the
rate of a service port, run the 

traffic table ip

 command to create a traffic profile

and then bind the profile to the service port.

huawei(config)#

service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 0 multi-

service 
user-vlan 8 rx-cttr 6 tx-cttr 6

huawei(config)#

service-port 2 vlan 8 gpon 0/2/1 ont 2 gemport 0 multi-

service 
user-vlan 8 rx-cttr 6 tx-cttr 6

7.

Confirm that the management channel between the OLT and the ONU is available.

–

On the OLT, run the 

ping  192.168.50.2

 and 

ping  192.168.50.3

 command to check

the connectivity to the ONU 1 and ONU 2. The ICMP ECHO-REPLY packet from
the ONU should be received.

–

You can run the 

telnet  192.168.50.2

 and 

telnet  192.168.50.3

 command to telnet

to the ONU 1 and ONU 2 and then configure the ONU.

8.

Configure the traffic profile.

You can run the 

display traffic table ip

 command to query the traffic profiles existing

in the system. If the traffic profiles existing in the system do not meet the requirements,
you need to run the 

traffic table ip

 command to add a traffic profile.

Add traffic profile 9, and no rate limitation on user packets. The priority is 6 and the
priority policy is scheduled by the priority that the packets bear.

huawei(config)#

traffic table ip index 9 cir off priority 6 priority-policy 

tag-In-Package

9.

Create a service port.

Create service port 200 connected to ONU 1 and service port 201 connected to ONU
2. SVLAN ID to 200, GEM port ID to 1, bind traffic profile 9 and CVLAN ID to 200.

NOTE

The CVLAN must be consistent with the upstream VLAN of the ONU.

huawei(config)#

service-port 200 vlan 200 gpon 0/2/1 ont 1 gemport 1 multi-

service user-vlan 200 rx-cttr 9 tx-cttr 9

huawei(config)#

service-port 201 vlan 200 gpon 0/2/1 ont 2 gemport 1 multi-

service user-vlan 200 rx-cttr 9 tx-cttr 9

10. Configure the queue scheduling mode.

Adopt the 3PQ+5WRR queue scheduling. Queues 0-4 adopt the WRR mode and their
weights are 10, 10, 20, 20, and 40 respectively. Queues 5-7 adopt the PQ mode. The
priority of the VoIP service is 6, adopting the PQ mode.

NOTE

l

The queue scheduling mode is configured globally, and you need to configure it only once on
the OLT. After the configuration is complete, the queue scheduling mode takes effect globally.
When subsequent services are configured, you need not configure the queue scheduling mode
again.

l

For a board that supports only four queues, the mapping between the 802.1p priorities and queue
IDs are as follows: priorities 0 and 1 map queue 1; priorities 2 and 3 map queue 2; priorities 4
and 5 map queue 3; priorities 6 and 7 map queue 4.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

526

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Panasonic MICROCOMPUTER MN103S Connection Diagrams preview
MICROCOMPUTER MN103S
Бренд: Panasonic Страницы: 5
Panasonic MICROCOMPUTER MN103S Application Note preview
MICROCOMPUTER MN103S
Бренд: Panasonic Страницы: 21
Panasonic FP2 Series Manual preview
FP2 Series
Бренд: Panasonic Страницы: 56
Panasonic FP2 Series Product Manual preview
FP2 Series
Бренд: Panasonic Страницы: 28
Panasonic KX-HTS Series Quick Start Manual preview
KX-HTS Series
Бренд: Panasonic Страницы: 2
Panasonic WJMPU955 - PROCESSING UNIT - TMU Operating Instructions Manual preview
WJMPU955 - PROCESSING UNIT - TMU
Бренд: Panasonic Страницы: 62
Abus TVVR36500 User Manual preview
TVVR36500
Бренд: Abus Страницы: 60
Dahua Smart 1U Quick Start Manual preview
Smart 1U
Бренд: Dahua Страницы: 24
Datasheen D902AC User Manual preview
D902AC
Бренд: Datasheen Страницы: 25
Endace DAG 7.1S User Manual preview
DAG 7.1S
Бренд: Endace Страницы: 51
Accom WSD/HDe Installation Procedure preview
WSD/HDe
Бренд: Accom Страницы: 15
IDT DBP 7+4 User Manual preview
DBP 7+4
Бренд: IDT Страницы: 93
Roland Super Sound Set SR-JV80-07 Owner'S Manual preview
Super Sound Set SR-JV80-07
Бренд: Roland Страницы: 8
Schrack Technik HSERG245GS Instruction Sheet preview
HSERG245GS
Бренд: Schrack Technik Страницы: 2
TDK HHM Series HHM2245SA1 Specifications preview
HHM Series HHM2245SA1
Бренд: TDK Страницы: 2
Idis DR-6308P Quick Manual preview
DR-6308P
Бренд: Idis Страницы: 20
Ubiquiti UniFi LED ULED-AT Quick Start Manual preview
UniFi LED ULED-AT
Бренд: Ubiquiti Страницы: 16
Tripp Lite N310-30M Specification Sheet preview
N310-30M
Бренд: Tripp Lite Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды