manualshive.com logo in svg

Huawei SmartAX MA5616, Руководство по настройке

"Huawei SmartAX MA5616" - высококачественное оборудование для настройки и управления сетями. Здесь вы можете бесплатно скачать "Configuration Manual" и другие руководства по использованию. Посетите manualshive.com, чтобы скачать нужные руководства.

Поделиться
Скачать
background image

The PITP function can be enabled or disabled at two levels. The PITP function is enabled only
when it is enabled at both levels.

1.

Global PITP function: Run the 

pitp enable pmode

 command to enable global PITP P mode.

By default, the global PITP function is disabled.
In the PITP V mode, run the 

pitp vmode ether-type

 command to set the Ethernet protocol

type to be the same as that of the BRAS. Then, run the 

pitp enable vmode

 command to

enable global PITP V mode.

NOTE

The Ethernet protocol type of the PITP V mode must be configured when the PITP V mode is disabled.

2.

(Optional) VLAN-level PITP function:

a.

Run the 

vlan service-profile

 command to create a VLAN service profile and enter

the VLAN service profile mode.

b.

Run the 

pitp enable

 command to enable the PITP function of the VLAN. By default,

the PITP function of the VLAN is enabled.

c.

Run the 

commit

 command to make the profile configuration take effect. The

configuration of the VLAN service profile takes effect only after this command is
executed.

d.

Run the 

quit

 command to quit the VLAN service profile mode.

e.

Run the 

vlan bind service-profile

 command to bind the VLAN service profile

configured in 

2.2.a

 to the VLAN.

Step 3

Configure the optional attributes of PITP.

l

Run the 

pitp permit-forwarding service-port

 command to set whether the service port

allows the user-side PPPoE packet carrying the vendor tag information. By default, this
function is disabled, that is, the user-side PPPoE packet carrying the vendor tag information
is not allowed.
The system adds a tag containing the device name, shelf ID, slot ID, and port ID to the PPPoE
+ upstream PADI and PADR packets to generate new packets. If this function is enabled,
tagged packets are forwarded. If this function is disabled, tagged packets are discarded.
When the PITP function is applied to the OLT+MA5616 network, pay attention to the
following points:

1.

When the PITP function is enabled only on the OLT, the tag of the PADI packet contains
only the information about the PON port on the OLT.

2.

When the PITP function is enabled only on the MA5616, the tag of the PADI packet
contains only the information about the user port on the MA5616.

3.

If the PITP function is enabled on both the OLT and the MA5616, a function (through
the 

pitp permit-forwarding service-port

 command) is used to choose which tag the

PADI packet carries.

–

When this function is enabled, the tag of the PADI packet contains only the
information about the PON port on the OLT.

–

When this function is disabled, subscribers connected to the service port fail to dial
a number. That is, the PADI packet (PITP P mode) cannot be transmitted.

l

Run the 

raio sub-option 0x90

 command to configure PITP sub-option 90. By default, PITP

sub-option 90 is disabled.
The PPPoE+ mode supports reporting the sub-option 90 line parameters, including link type
and encapsulation information. Enable or disable PITP sub-option 90 according to actual

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

82

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

NEC Express5800/E120d-M Getting Started preview
Express5800/E120d-M
Бренд: NEC Страницы: 2
IAR SYSTEMS IAR KickStart Kit TWR-K60N512-IAR Getting Started Manual preview
IAR KickStart Kit TWR-K60N512-IAR
Бренд: IAR SYSTEMS Страницы: 8
Avaya XM24 Expansion Module Installation Instructions preview
XM24 Expansion Module
Бренд: Avaya Страницы: 5
Paradyne Fan Tray 8820-S2-900 Installation Instructions Manual preview
Fan Tray 8820-S2-900
Бренд: Paradyne Страницы: 6
Xmart SNMP06 Reference Manual preview
SNMP06
Бренд: Xmart Страницы: 8
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Бренд: ADTRAN Страницы: 2
Magma ExpressBox2 EB2 User Manual preview
ExpressBox2 EB2
Бренд: Magma Страницы: 74
MiWire SeaWire Pro User Manual preview
SeaWire Pro
Бренд: MiWire Страницы: 24
Intel i960 Jx Developer'S Manual preview
i960 Jx
Бренд: Intel Страницы: 578
swiftech MCW5000-64RH Installation Manual preview
MCW5000-64RH
Бренд: swiftech Страницы: 2
LUX LUMEN 10230 Manual preview
10230
Бренд: LUX LUMEN Страницы: 41
Edimax GS-5208PLG V2 Quick Installation Manual preview
GS-5208PLG V2
Бренд: Edimax Страницы: 15
Cypress Semiconductor CY8C24223A Specification Sheet preview
CY8C24223A
Бренд: Cypress Semiconductor Страницы: 31
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Бренд: GSA Страницы: 101
Chaparral FS1310 User Manual preview
FS1310
Бренд: Chaparral Страницы: 96
ST STEVAL-SCR002V1 User Manual preview
STEVAL-SCR002V1
Бренд: ST Страницы: 28
PairGain 150-2230-01 Quick Installation Manual preview
150-2230-01
Бренд: PairGain Страницы: 48
Avocent Cyclades CS4008 Specifications preview
Cyclades CS4008
Бренд: Avocent Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды