Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 302 / 553

background image

Example

Assume that the link ID is 0, link set ID is 0, local port ID is 1402, local IP address is 10.10.10.10,
remote port ID is 1404, and remote IP address 1 is 10.10.10.20. To add such a link, do as follows:

huawei(config)#

sigtran

huawei(config-sigtran)#

iua-link add 0 0 1402 10.10.10.10 1404 10.10.10.20

huawei(config-sigtran)#

display iua-link attribute

{ <cr>|linkno<L> }:

Command:
display iua-link attribute
----------------------------------------------------------------------
LinkNo : 0
LinksetNo : 0
Local port : 1402
Local IP address : 10.10.10.10
Remote port : 1404
Remote IP address : 10.10.10.20
Remote IP address 2 : -
Bound MGC : -
Priority : 0
----------------------------------------------------------------------

7.3.3 Configuring the VoIP ISDN BRA User

This topic describes how to configure the VoIP ISDN BRA user. After the MG interface is
configured, you can add the VoIP ISDN BRA user on this interface to implement the VoIP ISDN
BRA service.

7.3.3.1 Configuring the ISDN BRA User Data

This topic describes how to configure the ISDN BRA user data based on H.248 (the data must
be the same as the corresponding data on the MGC) so that the ISDN BRA user can access the
network to use the ISDN BRA service.

Prerequisites

The H832DSLD service board must be inserted into the planned slot correctly and the board
must be in the normal state.

NOTE

You can run the

display board

command to query the board status.

l

If the query result is

Normal

, it indicates that the board is in the normal state.

l

If the query result is

Auto_find

, you need to run the

board confirm

command to confirm the board.

l

If the query result is

Failed

, handle the fault according to Service Board Is in the Failed State described

in the

Maintenance Guide

.

The working mode of the BRA port must be configured according to the requirements. For details
about how to configure the working mode of the BRA port, see

7.3.3.4 (Optional) Configuring

the Attributes of an ISDN BRA Port

Context

One H832DSLD board can be configured with a maximum of eight ISDN BRA users.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

291

«
...
300
301
302
303
304
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 30

Бренд: Sangoma Страницы: 6

xCORE-200 Multi-channel Audio board

Бренд: XMOS Страницы: 112

Бренд: A10 Страницы: 52

Бренд: Dahua Страницы: 6

MediaStream ConnectPlus 1000

Бренд: Avid Technology Страницы: 74

Бренд: NETGEAR Страницы: 2

Бренд: Idis Страницы: 31

Бренд: Patton electronics Страницы: 65

iW-RainboW-G30D

Бренд: iWave Страницы: 89

Бренд: Vivotek Страницы: 170

Бренд: Amplifier Tech Страницы: 36

Бренд: H3C Страницы: 26

Бренд: Direct IP Страницы: 76

Бренд: UHP Страницы: 15

Бренд: Ubiquiti Страницы: 21

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Бренд: Intel Страницы: 86

Бренд: BEC Страницы: 159

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды