manualshive.com logo in svg

Huawei SmartAX MA5616, Руководство по настройке

"Huawei SmartAX MA5616" - высококачественное оборудование для настройки и управления сетями. Здесь вы можете бесплатно скачать "Configuration Manual" и другие руководства по использованию. Посетите manualshive.com, чтобы скачать нужные руководства.

Поделиться
Скачать
background image

–

snr

: Indicates the SNR margin, which refers to the idle space for carrying noise,

excluding the space for carrying signals. In general, the SNR margin of the
minimum tone is considered as the SNR margin of the entire ADSL connection.

2.

Run the 

adsl channel-profile quickadd

 command to quickly add an ADSL2+ channel

profile, or run the interactive 

adsl channel-profile add

 command to add an ADSL2

+ channel profile.

Main parameters:

–

interleaved-delay

 and 

interleaving delay

 (in interactive mode): Indicates the

interleave delay. A zero interleave delay corresponds to the fast mode. In the fast
mode, the interleave delay is short, but the error correction capability is weak. A
non-zero interleave delay corresponds to the interleave mode. The interleave depth
increases directly to the interleave delay. In the interleave mode, higher interleave
depth indicates more powerful error correction capability but longer interleave
delay.

–

inp

: Indicates impulse noise protection. As a parameter that describes the line

capability of resisting impulse interference, INP affects the port rate. If INP is 1,
it indicates that the current channel can resist the impulse noise in 1 DMT character
length. The interleave delay is related to INP. In the fast mode, INP does not apply.

–

rate

: Indicates the line rate. During line activation, a proper rate between the preset

maximum rate and minimum rate is determined through automatic negotiation
according to the line condition and the profile configuration. The user rate can be
restricted by this line rate or the rate set in the traffic profile bound to the user.
When both rates function, the lower one is adopted as the user rate.

3.

Run the 

adsl line-template quickadd

 command to quickly add an ADSL+ line

template, or run the interactive 

adsl line-template add

 command to add an ADSL2

+ line template.

An ADSL2+ line template is formed by binding an ADSL2+ line profile with an
ADSL2+ channel profile. An ADSL2+ port needs to be bound to only an ADSL2+
line template.

l

Configure an ADSL2+ line alarm template.
1.

Run the 

adsl alarm-profile quickadd

 command to quickly add an ADSL2+ line alarm

profile, or run the interactive 

adsl alarm-profileadd

 command to add an ADSL2+

line alarm profile.

2.

Run the 

adsl channel-alarm-profile quickadd

 command to quickly add an ADSL2

+ channel alarm profile, or run the interactive 

adsl channel-alarm-profile add

command to add an ADSL2+ channel alarm profile.

3.

Run the 

adsl alarm-template quickadd

 command to quickly add an ADSL2+ line

alarm template, or run the interactive 

adsl alarm-templateadd

 command to add an

ADSL2+ line alarm template.

An ADSL2+ alarm template is formed by binding an ADSL2+ line alarm profile with
an ADSL2+ channel alarm profile. An ADSL2+ port needs to be bound with only an
ADSL2+ alarm template.

----End

Example

Assume that an ADSL2+ line template with an index number of 3 is to be added. For the ADSL2
+ line template, the downstream rate is 2048 kbit/s, the channel mode is the interleave mode,

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

59

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

IBM 3270 Operation Manual preview
3270
Бренд: IBM Страницы: 86
Acconeer A111 User Manual preview
A111
Бренд: Acconeer Страницы: 32
Nayar Systems GSR Manual preview
GSR
Бренд: Nayar Systems Страницы: 37
NavigateWorx NR300 User Manual preview
NR300
Бренд: NavigateWorx Страницы: 71
Velopex Extra-X Quick Start Manual preview
Extra-X
Бренд: Velopex Страницы: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Бренд: Tandberg Data Страницы: 6
u-blox ANT-B10 User Manual preview
ANT-B10
Бренд: u-blox Страницы: 29
Seattle Computer Products 8086 CPU Instruction Manual preview
8086 CPU
Бренд: Seattle Computer Products Страницы: 31
Cisco MERAKI MX450 Installation Manual preview
MX450
Бренд: Cisco MERAKI Страницы: 4
StarTech.com ST1000SMPEX Instruction Manual preview
ST1000SMPEX
Бренд: StarTech.com Страницы: 9
XtendLan XL-HCW224C User Manual preview
XL-HCW224C
Бренд: XtendLan Страницы: 52
Ubiquiti PowerBeam PBE-5AC-400-ISO Quick Start Manual preview
PowerBeam PBE-5AC-400-ISO
Бренд: Ubiquiti Страницы: 23
DCB BROADCAST POLLING FRAD BPF-14 BU Manual preview
BROADCAST POLLING FRAD BPF-14 BU
Бренд: DCB Страницы: 28
BinTec BIANCA/BRI Getting Started preview
BIANCA/BRI
Бренд: BinTec Страницы: 34
Loopcomm LP-8014 Quick Start Manual preview
LP-8014
Бренд: Loopcomm Страницы: 2
H3C BT1004E Manual preview
BT1004E
Бренд: H3C Страницы: 34
Multi-Link Power Stone Programming Manual preview
Power Stone
Бренд: Multi-Link Страницы: 31
MicroNova O047 Technical Installation Manual preview
O047
Бренд: MicroNova Страницы: 113

Бренды по названию

Популярные бренды

Загрузить еще бренды