Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 471 / 553

background image

6
tx-cttr 6
service-port 1 vlan 101 vdsl mode ptm 0/1/3 multi-service user-encap pppoe rx-cttr
6
tx-cttr 6

Set the inner VLAN tag.

stacking label service-port 0 11
stacking label service-port 1 12

9.5 Configuring the Triple Play Service

This topic describes the triple play service and how to configure the triple play service on the
MA5616 on the GE upstream transmission network.

9.5.1 Configuration Example of the Triple Play Service - Single PVC
for Multiple Services Based on the User-Side VLAN

This topic describes how to configure the triple play service in the single-PVC for multiple
services mode based on the user-side VLAN.

Prerequisites

Before configuring the triple play service, make sure that:

l

The network devices and lines are in the normal state.

l

The CPE is already configured (the CPE supports different VLANs for different services).

l

All boards of the device run in the normal state.

l

The VDSL2 line template and alarm template that are bound to the port are already
configured. For details on the configuration procedure, see

3.7.3 Configuring the VDSL2

Service Requirements

l

The MA5616 is used on the GE upstream transmission network.

l

VDSL2 user 1 and VDSL2 user 2 are connected to the MA5616 to implement the triple
play.

l

The Internet service is accessed in the PPPoE mode.

l

After receiving different traffic streams through the same PVC, the MA5616 provides
different QoS guarantees to the traffic streams according to the user-side VLANs.

Networking

Figure 9-12

shows the example network for configuring the triple play service based on the

user-side VLAN.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

460

«
...
469
470
471
472
473
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: TC Electronic Страницы: 55

Бренд: Blackrock Microsystems Страницы: 27

Бренд: SMART Страницы: 15

Бренд: SUNRICH TECHNOLOGY Страницы: 5

Бренд: ESD Страницы: 28

Бренд: Davey Страницы: 18

Бренд: ebm-papst Страницы: 11

Elite Controller

Бренд: RANA Systems Страницы: 328

4 Channel Input Buffer Board SDAIBB

Бренд: B&B Electronics Страницы: 22

Бренд: Idis Страницы: 22

OptiBond 210 C Series

Бренд: i-MO Страницы: 16

DEEP LEARNING PLUS

Бренд: Concept Pro Страницы: 28

Бренд: Dataprobe Страницы: 16

Бренд: Zoom Страницы: 2

Бренд: SMC Networks Страницы: 56

Бренд: Kaya Instruments Страницы: 48

Бренд: Zhone Страницы: 53

Бренд: Uctronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды