Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 383 / 553

background image

Configuration File

The following describes the configuration file of this configuration example. Note that certain
steps must be performed manually and the configuration file cannot be imported directly.

Create VLANs.

vlan 100 to 101 smart

Set the VLAN attribute.

vlan attrib 100 to 101 stacking

Add an uplink port to VLANs.

port vlan 100 to 101 0/0 1

Add service ports to VLANs.

vlan 100 to 101 smart
vlan attrib 100 to 101 stacking
port vlan 100 to 101 0/0 1
service-port 1 vlan 100 vdsl mode ptm 0/1/0 multi-service user-encap pppoe  rx-cttr
6
tx-cttr 6
service-port 2 vlan 100 vdsl mode ptm 0/1/1 multi-service user-encap pppoe  rx-cttr
6
tx-cttr 6
service-port 3 vlan 101 vdsl mode ptm 0/1/2 multi-service user-encap pppoe  rx-cttr
6
tx-cttr 6
service-port 4 vlan 101 vdsl mode ptm 0/1/3 multi-service user-encap pppoe  rx-cttr
6
tx-cttr 6

Set inner VLAN tag.

stacking label service-port 1 11
stacking label service-port 2 12
stacking label service-port 3 11
stacking label service-port 4 12

8.4.2 Configuration Example of the VLAN ID Extension Service

This topic describes how to configure the VLAN ID extension for increasing the number of users
that can be identified according to the VLAN ID by the BRAS.

Prerequisites

l

Network devices and lines must be in the normal state.

l

The authentication data of the access user must be configured on the BRAS.

l

The control board and the involved service boards must be in the normal state.

Context

In the application of the VLAN ID extension, the outer and inner VLAN tags are used to identify
the user, or the outer VLAN tag is used to identify the access device and the inner tag is used to
identify the users that access the device. The BRAS identifies the access users based on the L2
VLAN tag to increase the number of users identified by the VLAN ID, thus increasing the
number of users that access the BRAS.

In this example, outer VLAN tags 100 and 101 identify MA5616_A and MA5616_B
respectively, and an inner VLAN tag identifies a device user.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

372

«
...
381
382
383
384
385
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: NEC Страницы: 10

Бренд: NEC Страницы: 8

Бренд: Quatech Страницы: 27

Optane M Series

Бренд: Intel Страницы: 59

Бренд: DAD Страницы: 32

Sentry Global Security Modem

Бренд: Server Technology Страницы: 22

Бренд: Qixiang Technology Страницы: 16

Бренд: 8level Страницы: 52

Бренд: Hama Страницы: 6

Бренд: ADS Technologies Страницы: 1

Бренд: Nilox Страницы: 66

Бренд: ZyXEL Communications Страницы: 2

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 2

Бренд: ADTRAN Страницы: 20

Бренд: ETAS Страницы: 36

Бренд: Cowlacious Designs Страницы: 8

IntraSwitch 5324MT

Бренд: Asante Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды