Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 231 / 553

background image

Table 7-4

Software parameters of an MG interface that supports H.248

Parameter

Description

Default Setting

2

Indicates whether the MG
interface supports dual homing.
To configure an MG interface
to or not to support dual
homing, use this parameter.
This parameter can be
configured only when the MG
interface is in the local closed
state.
If the MG interface does not
support dual homing, even if the
secondary MGC is configured,
the MG interface does not
switch to registering with the
secondary MGC when the MG
interface fails to register with
the primary MGC. If the MG
interface supports dual homing
and auto-switching, even if the
MG interface has registered
with the secondary MGC, the
MG interface can automatically
switch back to the primary
MGC if the primary MGC
recovers. If the MG interface
supports dual homing, you can
run the

mgc_switch(h248)

command to perform the MGC
switching.

Numeral type. Range: 0-2.

l

0: Indicates that dual homing
is not supported.

l

1: Indicates that dual homing
rather than auto-switching is
supported.

l

2: Indicates that dual homing
and auto-switching is
supported.

Default: 0

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

220

«
...
229
230
231
232
233
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

Бренд: mikroElektronika Страницы: 3

Бренд: Opengear Страницы: 2

HHM Series HHM2411

Бренд: TDK Страницы: 2

AT-8550/SP Series

Бренд: Allied Telesis Страницы: 114

Бренд: Belkin Страницы: 57

Бренд: Softing Страницы: 4

Бренд: ETAS Страницы: 84

Бренд: VideoWave Страницы: 12

Бренд: uneron Страницы: 13

LatticeMico GPIO

Бренд: Lattice Semiconductor Страницы: 28

Бренд: Goobay Страницы: 20

Data Capture Board CLC-CAPT-PCASM

Бренд: National Semiconductor Страницы: 15

-K6-2/450 - MHz Processor

Бренд: AMD Страницы: 98

Бренд: Boser Страницы: 82

Бренд: IBM Страницы: 78

SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz

Бренд: Intel Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды