Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 229 / 553

background image

Table 7-3

Digitmap format in the H.248 protocol

Digit or
Character

Description

0-9

Indicate dialed digits 0-9.

A-D

Indicate A-D.

E

Indicates * in the DTMF mode.

F

Indicates for # in the DTMF mode.

X

Indicates for a wildcard, indicating any digit from 0 to 9.

S

Indicates the short timer. When detecting the timer timeout, the system reports
a phone number digit by digit if the phone number is detected after the dialing
scheme is matched. The short timer is applied when the collected number
matches at least one dialing scheme, but more numbers may be received and
these numbers match other dialing schemes.

L

Indicates the long timer. When detecting the timer timeout, the system reports
a phone number digit by digit if the phone number is detected after the dialing
scheme is matched. The long timer is applied when the dialed number does
not match any dialing scheme.

Z

Indicates the duration modifier, which indicates a dialing event of a long
duration. It is before the event character with a fixed location. When the event
duration exceeds the threshold, the dialing event fills the location.

.

Indicates that there can be multiple digits (including 0) or characters before
it.

|

Used to separate the strings and indicates that each string is an optional dialing
scheme.

[]

Indicates that one digit or string can be selected from the options.

Procedure

Step 1

Enter the MG interface mode.

In global config mode, run the

interface h248

command to enter the MG interface mode.

Step 2

Configure the digitmap.

Run the

digitmap set

command to configure the digitmap required in the data plan.

Step 3

(Optional) Configure the digitmap timer.

Run the

digitmap-timer

command to configure the digitmpa timer.

Generally, the digitmap is issued by the MGC. In this case, the issued digitmap timer prevails
regardless of whether a timer is configured on the AG. When the MGC does not issue the
digitmap timer and the default digitmap timer does not meet the service requirements, you can
configure the digitmap timer in this step.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

218

«
...
227
228
229
230
231
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Express Ethernetwork DI-704P

Бренд: D-Link Страницы: 17

Бренд: Hama Страницы: 10

Бренд: Quatech Страницы: 27

Бренд: XESS Страницы: 23

Бренд: Watchguard Страницы: 30

Бренд: Lucent Technologies Страницы: 20

Бренд: Lanner electronics Страницы: 59

Elite Controller

Бренд: RANA Systems Страницы: 328

Бренд: Cervoz Страницы: 22

Quadro M6000 Sync

Бренд: Nvidia Страницы: 8

SiliconDrive SSD-P16G(I)-3100

Бренд: Silicon Systems Страницы: 108

Бренд: IBM Страницы: 34

Бренд: Advantech Страницы: 68

Бренд: Navitar Страницы: 1

Бренд: Tenda Страницы: 120

Бренд: Z-Wave Страницы: 42

Бренд: Hologic Страницы: 256

Бренд: Black Box Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды