Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 46 / 553

background image

l

If the device is interconnected with the NMS through the GE upstream port in inband
networking mode, the communication port (GE upstream port) must be configured. For
detailed procedure, see

3.1.4 Configuring Inband Management (GE Upstream)

Networking - Inband Networking Mode

As shown in the inband networking in

3.2.1 Configuring the U2000 (Based on SNMPv1)

, the

SNMP protocol is transmitted through the service channel. Service packets and management
packets are transmitted through the same channel. The inband NMS management is implemented
through the upstream port.

l

The MA5616 supports GPON/GE upstream port.

l

A static route is used between the MA5616 and the U2000.

Networking - Outband Networking Mode

As shown in the outband networking in

3.2.1 Configuring the U2000 (Based on SNMPv1)

,

the SNMP protocol is transmitted through the management channel. Service packets and
management packets are transmitted through different channels. The outband NMS management
is implemented through the maintenance network port.

l

The MA5616 supports the local maintenance network port ETH.

l

A static route is used between the MA5616 and the U2000.

Configuration Flowchart

To configure the NMS, see the flowchart for configuring the NMS in

3.2.1 Configuring the

U2000 (Based on SNMPv1)

.

Procedure

l

Configuration procedure on the device
1.

Configure the SNMP parameters.

a.

Configure the community names and the access rights.
Run the

snmp-agent community

command to configure the community names

and the access rights.

NOTE

The read community name is

public

. The write community name is

private

.

The read community name and the write community name on the device must be the
same as those configured on the U2000.

huawei(config)#

snmp-agent community read public

huawei(config)#

snmp-agent community write private

b.

(Optional) Set the information about the administrator.
Run the

snmp-agent sys-info

command to set the contact of the SNMP Agent

administrator and the physical position of the device.
Contact of the administrator: HW-075528780808. Physical position of the
device: Shenzhen_China.

huawei(config)#

snmp-agent sys-info contact HW-075528780808

huawei(config)#

snmp-agent sys-info location Shenzhen_China

c.

Set the SNMP version.
Run the

snmp-agent sys-info

command to set the required SNMP version.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

35

«
...
44
45
46
47
48
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: TC Electronic Страницы: 2

Бренд: Aastra Страницы: 2

Бренд: DBM Страницы: 50

Бренд: D-Link Страницы: 83

Бренд: Hawking Страницы: 2

Бренд: Netopia Страницы: 38

Бренд: IBM Страницы: 32

JetWeb JX2-PR0FI1

Бренд: Jetter Страницы: 67

AT-9424Ts/XP AC

Бренд: Allied Telesis Страницы: 3

LoadMaster 1500

Бренд: KEMP Technologies Страницы: 71

Бренд: Roland Страницы: 12

Бренд: H3C Страницы: 400

Бренд: BSD Networks Страницы: 7

HIRESCHMANN IT MAMMUTHUS MTM8003-FAN

Бренд: Belden Страницы: 84

Mercury FireWire 400

Бренд: OWC Страницы: 2

Бренд: MICROENER Страницы: 24

Бренд: Zoom Страницы: 31

Бренд: Microtek Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды