Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 316 / 553

background image

This reduces delay, improves the performance of transparent transmission, and decreases
the impact of packet loss on the transmission of the modem service data.

l

RFC 2198 function: Through the redundant transmission, the RFC 2198 improves the
reliability of data transmission. When the network packet loss occurs, the RFC 2198 can
ensure the service quality.

The MoIP service supports two transmission modes: the transparent transmission mode and the
relay (redundancy) mode. The MA5616 supports only the modem service in the transparent
transmission mode. In the transparent transmission mode, the MG uses the G.711 mode to encode
and decode the modem signal, and processes the signal like processing the common RTP data.
The transparent transmission mode depends on the bearer network to a great extent.

Procedure

Step 1

Configure public fax and modem parameters.
1.

Run the

interface sip

command to enter the SIP interface mode.

2.

Run the

fax-modem parameters negomode

command to configure the negotiation mode.

3.

(Optional) Run the

fax-modem parameters packet-interval-10ms

to enable or disable

the 10 ms packing function.

4.

(Optional) Run the command to configure the RFC 2198 function.

5.

(Optional) Run the command to configure the startup mode of the RFC 2198 function.

6.

(Optional) Run the

fax-modem parameters vbd-codec

command to configure the codec

mode of the voice-band data (VBD).

7.

(Optional) Run the

fax-modem parameters vbd-pt-type

command to configure the

payload type of the VBD.

8.

(Optional) Run the

rfc2833 set rfc2833-fax-modem

command to configure the mode for

reporting fax or modem events.

Step 2

Configure the transmission mode of the modem.

Run the

modem parameters tranmode

command to configure the transmission mode of the

modem. Currently, only the modem service in the transparent transmission mode is supported.

Step 3

Check whether the modem parameters are the same as those in the data plan.

Run the

display fax-modem parameters

and

display modem parameters

commands to query

modem parameters.

----End

Example

Assume that:

l

The negotiation mode of the MA5616 is self-switch.

l

The 10 ms packing function and the RFC2198 intelligent startup function are enabled.

l

The RFC2198 negotiation mode is fixedstart.

l

The codec mode of the VBD is G.711A.

l

The payload type of the VBD is static payload.

l

The transmission mode of the modem is transparent transmission (thoroughly).

To configure the MA5616, do as follows:

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

305

«
...
314
315
316
317
318
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: CAME Страницы: 4

Бренд: LAWO Страницы: 154

Бренд: Sangoma Страницы: 6

Бренд: Planet Страницы: 20

Fast SwitchHub-8mi SNMP

Бренд: Accton Technology Страницы: 13

PG-FlexPlus AMU-912

Бренд: ADC Страницы: 130

Бренд: Fieldbus Specialists Страницы: 39

Бренд: Fracarro Страницы: 12

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 2

Бренд: Neo Instruments Страницы: 2

Dimension ES-3124

Бренд: ZyXEL Communications Страницы: 228

Бренд: IDT Страницы: 93

EK-Loop Modulus Series

Бренд: ekwb Страницы: 7

Бренд: MICROENER Страницы: 24

airHaul Nexus sB3010

Бренд: SmartBridges Страницы: 80

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Бренд: Intel Страницы: 112

Бренд: Active Communications Страницы: 10

Бренд: XAVI Technologies Corp. Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды