Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 330 / 553

background image

channel mode is the interleave mode, maximum downstream interleave delay is 8 ms,
maximum upstream interleave delay is 2 ms, SNR margin is 6 dB, minimum downstream
INP is 4, and minimum upstream INP is 2.

huawei(config)#

vdsl line-profile quickadd 3 snr 60 0 300 60 0 300

huawei(config)#

vdsl channel-profile quickadd 3 path-mode ptm interleaved-delay

8 2 inp 4 2 rate
128 10000 128 10000 2048 2048

huawei(config)#

vdsl line-template quickadd 3 line 3 channel1 3 100 100

2.

Activate VDSL port 0/1/0, and bind the preset VDSL line template 3 and the default VDSL
alarm template (alarm template 1) to the port.

NOTE

By default, a VDSL port is in the activated state. Before binding a template to the port, you must deactivate
the port.

huawei(config)#

interface vdsl 0/1

huawei(config-if-vdsl-0/1)#

deactivate 0

huawei(config-if-vdsl-0/1)#

activate 0 template-index 3

huawei(config-if-vdsl-0/1)#

alarm-config 0 1

huawei(config-if-vdsl-0/1)#

quit

3.

Run the

display traffic table

command to query the existing traffic profiles in the system.

huawei(config)#

display traffic table ip from-index

0

{ <cr>|to-
index<K> }:


Command:
display traffic table ip from-index
0

----------------------------------------------------------------------------
TID CIR(kbps) CBS(bytes) PIR(kbps) PBS(bytes) Pri Copy-policy Pri-
Policy

----------------------------------------------------------------------------
0 1024 34768 2048 69536 6 - tag-
pri
1 2496 81872 4992 163744 6 - tag-
pri
2 512 18384 1024 36768 0 - tag-
pri
3 576 20432 1152 40864 2 - tag-
pri
4 64 4048 128 8096 4 - tag-
pri
5 2048 67536 4096 135072 0 - tag-
pri
6 off off off off 0 - tag-
pri

----------------------------------------------------------------------------
Total Num : 7

According to service requirements, the user access rate is 2048 kbit/s. The query result
shows that traffic profile 5 (for inbound and outbound rate limitation) meets the
requirements.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

319

«
...
328
329
330
331
332
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

Бренд: T&D Страницы: 122

Бренд: Ubiquiti Страницы: 22

Бренд: Ublox Страницы: 17

Бренд: Commell Страницы: 58

Procont LMC-008-IO

Бренд: janitza Страницы: 28

Net2Air Ins-40085-US

Бренд: Paxton Страницы: 4

Бренд: ZyXEL Communications Страницы: 215

Бренд: B&B Electronics Страницы: 2

Бренд: ZALMAN Страницы: 7

Octopus G Series

Бренд: TwinMOS Страницы: 29

Бренд: Xantech Страницы: 4

E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010

Бренд: Juniper Страницы: 122

Бренд: eWON Страницы: 34

JetStor NAS 724UX

Бренд: AC&NC Страницы: 117

Бренд: Ubiquiti Страницы: 23

Бренд: Cypress Semiconductor Страницы: 19

B-Control Fader BCF2000

Бренд: Behringer Страницы: 13

Бренд: NETGEAR Страницы: 152

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды