Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 151 / 553

background image

NOTE

Before adding a user-defined analog or digital monitoring parameter, make sure that the port corresponding
to this analog or digital monitoring parameter is properly connected with an environment monitoring cable.

Procedure

Step 1

Add the EPS30-4815AF, namely, Power4830.

Run the

emu add

command to add the Power4830.

Step 2

In the environment monitoring configuration mode, run the

display power system

parameter

command to query the default configuration.

Step 3

Configure the parameters of the lead battery.

Run the

power battery parameter

command to configure battery parameters, including battery

management parameters, charging parameters and battery set power-off parameters, and battery
high-temperature power-off parameters. You can also use the default settings.

Step 4

Configure the parameter of the rectifier unit.

Run the

power module-num

command to configure the parameter of the rectifier unit.

Step 5

Configure the environment parameters for power supply monitoring.

Run the

power environment

command to configure the upper and lower alarm thresholds and

measurement thresholds of temperature or humidity for power monitoring. In this manner, the
power module generates alarms when it works in a condition that does not meet the present
requirements.

Step 6

Configure the external extended digital parameter for power supply monitoring.

Run the

power outside_digital

command to configure the external extended digital parameter

for power supply monitoring.

Step 7

Query configuration parameters and environment parameters of the power system.

Run the

display power system parameter

command to query configuration parameters of the

power monitoring unit.

Step 8

Run the

display power alarm

command to query the alarm. Ensure that no alarm (except the

door status alarm) for the monitoring parameter is generated.

Step 9

Save the data.

Run the

quit

command to quit the Power4830 mode, and then run the

save

command to save

the data.

----End

Result

After the configuration, the EPS30-4815AF works in the normal state and monitors parameters
set on the MA5616. When a monitored parameter is abnormal, the MA5616 reports an alarm.

Example

provides the data plan for configuring the power monitoring through the

EPS30-4815AF.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

140

«
...
149
150
151
152
153
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

BiPAC 4500NZ(L)

Бренд: Billion Страницы: 146

Бренд: Farallon Страницы: 26

Бренд: Observint Страницы: 11

Бренд: IBM Страницы: 32

ADSL 2/2+ Router with USB Port ADE-3410v2

Бренд: Planet Страницы: 62

Бренд: TP-Link Страницы: 3

ThunderLAN TNETE100A

Бренд: Texas Instruments Страницы: 179

Бренд: Klark Teknik Страницы: 50

Бренд: Oracle Страницы: 112

Бренд: peplink Страницы: 2

AIE900-XNX Series

Бренд: AXIOMTEK Страницы: 53

Бренд: 1&1 Страницы: 32

WNFB-265AXI(BT)

Бренд: Sparklan Страницы: 14

Бренд: AirTies Страницы: 28

Бренд: Nakayo Страницы: 119

NOVA300 AML02304U1

Бренд: Nexxt Страницы: 75

PCard-E 021L-D5 Series

Бренд: ORiNG Страницы: 2

Бренд: Perle Страницы: 491

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды