manualshive.com logo in svg

Huawei SmartAX MA5616, Руководство по настройке

"Huawei SmartAX MA5616" - высококачественное оборудование для настройки и управления сетями. Здесь вы можете бесплатно скачать "Configuration Manual" и другие руководства по использованию. Посетите manualshive.com, чтобы скачать нужные руководства.

Поделиться
Скачать
background image

     3       576      20432      1152      40864   2 -              tag-pri     
     4        64       4048       128       8096   4 -              tag-pri     
     5      2048      67536      4096     135072   0 -              tag-pri     
     6       off        off       off        off   0 -              tag-pri     
  ----------------------------------------------------------------------------  
  Total Num : 7 
huawei(config)#

traffic table ip index 8 cir 3072 priority 4 priority-policy loca

l-Setting 

                                                                      

  Create traffic descriptor record successfully                                 
  ------------------------------------------------                              
  TD Index             : 8                                                      
  TD Name              : ip-traffic-table_8                                     
  Priority             : 4                                                      
  Mapping Priority     : -                                                      
  Mapping Index        : -                                                      
  CTAG Mapping Priority: -                                                      
  CTAG Mapping Index   : -                                                      
  CTAG Default Priority: 0                                                      
  Priority Policy      : local-pri                                              
  CIR                  : 3072 kbps                                              
  CBS                  : 100304 bytes                                           
  PIR                  : 6144 kbps                                              
  PBS                  : 198608 bytes                                           
  Referenced Status    : not used                                               
  ------------------------------------------------   
huawei(config)#

service-port 3 vlan 100 adsl 0/2/0 vpi 1 vci 39 inbound traffic-

table index 8 outbound traffic-table index 8 

huawei(config)#

mac-address max-mac-count service-port 3 2

huawei(config)#

service-port 3 adminstatus disable 

A residential user requests the Internet access service with the access rate 2048 kbit/s. To
facilitate service expansion in the future, the MA5616 adopts the ADSL2+ mode to provide the
Internet access service for the user and differentiates users by user-side VLAN (the S-VLAN is
VLAN 50 and the C-VLAN is VLAN 10). Query result shows that the system has a proper traffic
profile. Therefore, the system provides the Internet access service for the user immediately. To
facilitate maintenance, configure description for the service port.

huawei(config)#

display traffic table ip from-index 0  

  

{ <cr>|to-index<K> }:                                                           
                                                                                
  Command:                                                                      
          display traffic table ip from-index 0                                 
  ----------------------------------------------------------------------------  
   TID CIR(kbps) CBS(bytes) PIR(kbps) PBS(bytes) Pri Copy-policy    Pri-Policy  
  ----------------------------------------------------------------------------  
     0      1024      34768      2048      69536   6 -              tag-pri     
     1      2496      81872      4992     163744   6 -              tag-pri     
     2       512      18384      1024      36768   0 -              tag-pri     
     3       576      20432      1152      40864   2 -              tag-pri     
     4        64       4048       128       8096   4 -              tag-pri     

     5      2048      67536      4096     135072   0 -              tag-pri     

     6       off        off       off        off   0 -              tag-pri     
  ----------------------------------------------------------------------------  
  Total Num : 7 
huawei(config)#

service-port 4 vlan 50 adsl 0/2/0 vpi 1 vci 39 multi-service 

user-vlan 10 inbound traffic-table index 5 outbound traffic-table index 5  

huawei(config)#

service-port desc 4 description HW_adsl/VlanID:50/uservlan/10

A residential user requests the Internet access service with the access rate 2048 kbit/s. To
facilitate service expansion in the future, the MA5616 adopts the SHDSL mode to provide the
Internet access service for the user. Query result shows that the system has a proper traffic profile.
Therefore, the system provides the Internet access service for the user immediately. To facilitate
maintenance, configure description for the service port.

huawei(config)#

display traffic table ip from-index 0  

 

{ <cr>|to-index<K> }:                                                           
                                                                                

SmartAX MA5616 Multi-service Access Module
Configuration Guide

5 Configuring the xDSL Internet Access Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

171

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

D-Link DSL-504T Manual preview
DSL-504T
Бренд: D-Link Страницы: 99
D-Link DI-804V Datasheet preview
DI-804V
Бренд: D-Link Страницы: 5
D-Link DES-1210-08P Manual preview
DES-1210-08P
Бренд: D-Link Страницы: 15
D-Link AirPro DWL-6000AP Manual preview
AirPro DWL-6000AP
Бренд: D-Link Страницы: 65
Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Бренд: Paradyne Страницы: 2
Paradyne Hotwire 6381 Installation Instructions Manual preview
Hotwire 6381
Бренд: Paradyne Страницы: 20
Paradyne Hotwire 6381 Upgrade Instructions preview
Hotwire 6381
Бренд: Paradyne Страницы: 2
Zhone Hotwire 6381 Quick Installation Instructions preview
Hotwire 6381
Бренд: Zhone Страницы: 2
Renesas F-ZTAT H8/3048 Series User Manual preview
F-ZTAT H8/3048 Series
Бренд: Renesas Страницы: 34
National Instruments NI-9252 Calibration Procedure preview
NI-9252
Бренд: National Instruments Страницы: 9
Allied Telesis AT-8000C Declaration Of Conformity preview
AT-8000C
Бренд: Allied Telesis Страницы: 1
Campbell NL115 User Manual preview
NL115
Бренд: Campbell Страницы: 38
Grizzly PSJ-M3 GEN2 User Manual preview
PSJ-M3 GEN2
Бренд: Grizzly Страницы: 9
Olicom Ethernet MCA 10/100 Adapter Manual To Operations preview
Ethernet MCA 10/100 Adapter
Бренд: Olicom Страницы: 88
EZCast Pro Dongle II User Manual preview
Pro Dongle II
Бренд: EZCast Страницы: 24
Lindy Modular Fast Fiber Switch Converter MT-RJ Specifications preview
Modular Fast Fiber Switch Converter MT-RJ
Бренд: Lindy Страницы: 3
Freescale Semiconductor KW2xD Series Reference Manual preview
KW2xD Series
Бренд: Freescale Semiconductor Страницы: 42
R.V.R. Elettronica PTX30-UHT Installation, Technical And Maintenance Manual preview
PTX30-UHT
Бренд: R.V.R. Elettronica Страницы: 171

Бренды по названию

Популярные бренды

Загрузить еще бренды