Huawei SmartAX MA5616 Скачать руководство пользователя | Manualshive

Страница: 242 / 553

background image

Example

Assume that in the H.248 mode, the terminal prefix of the PSTN user on MG interface 1 is aln/,
and the layering TID template 3 is used. To add a PSTN user on port 0/2/0 and check whether
the system automatically allocates a TID generated according to the template, do as follows:

huawei(config)#

display tid-template 3

// Query the information about the TID

template 3.
-------------------------------------------------
Index : 3
Format : %u/%u/%u
Para-list : F+1,S+1,P+1 //

Keywords in the parameter list of the TID template

are “F”, “S”, and “P”.

Name : Aln_Not_Fixed_1
-------------------------------------------------
huawei(config)#

interface h248 1

huawei(config-if-h248-1)#

tid-format pstn prefix aln/ template 3

huawei(config-if-h248-1)#

quit

huawei(config)#

esl user

huawei(config-esl-user)#

mgpstnuser add 0/2/0 1

huawei(config-esl-user)#

display mgpstnuser 0/2/0

{ <cr>|endframeid/slotid/portid<S><Length
1-15> }:

Command:
display mgpstnuser 0/2/0
----------------------------------------------------------------------------
F /S /P MGID TelNo Priority PotsLineType TerminalID
----------------------------------------------------------------------------
0 /2 /0 1 - Cat3 DEL aln/1/3/1
----------------------------------------------------------------------------

7.1.1.8 Enabling an MG Interface

Enabling an MG interface is to reset an MG interface to make the MG interface register with
the MGC (or to make the modified attributes of the MG interface take effect) after the
configuration of the MG interface is complete, so that the MG interface can work in the normal
state.

Precaution

CAUTION

For the MG interface that has been in service, this operation interrupts the ongoing services
carried on the MG interface. Hence, exercise caution when performing this operation.

Procedure

Step 1

Enter the H248 mode.

Run the

interface h248

command to enter the H248 mode.

Step 2

Enable the MG interface.

Run the

reset coldstart

command to enable the MG interface.

Step 3

Check the state of the MG interface.

You can query the status of the MG interface by using one of the following two methods.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

231

«
...
240
241
242
243
244
...
»

Содержание SmartAX MA5616










































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartAX MA5616

RouterBOARD Groove

Бренд: MikroTik Страницы: 4

Бренд: Alacritech Страницы: 20

Sure Cross DX70

Бренд: Banner Страницы: 35

Бренд: Altera Страницы: 42

ConnectX-3 Pro MCX349A-XCCN

Бренд: Mellanox Technologies Страницы: 35

2000 IDU Series

Бренд: EMS Страницы: 52

J-Link-OB-STM32F072-128KB

Бренд: Segger Страницы: 18

CHEETAH ST34501FC

Бренд: Seagate Страницы: 68

Бренд: H3C Страницы: 68

Бренд: Keysight Technologies Страницы: 106

Бренд: Xilinx Страницы: 29

Бренд: HMS Страницы: 18

Бренд: Intel Страницы: 20

Бренд: ST Страницы: 67

Бренд: Matrix Switch Corporation Страницы: 48

HHM Series HHM1521

Бренд: TDK Страницы: 2

Бренд: Disc Makers Страницы: 12

DVP Series PLC DVP04TC-H2

Бренд: Delta Electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды